Sintering behaviour of 3D-printed 18K 5N gold alloy by binder jetting: a preliminary study

[1]  N. Kalentics,et al.  Understanding variant selection and texture in additively manufactured red-gold alloys , 2022, Scripta Materialia.

[2]  M. Garcia-Blanco,et al.  A study of parameter and post-processing effects on surface quality improvement of Binder Jet 3D-printed Invar36 alloy parts , 2022, Progress in Additive Manufacturing.

[3]  E. Olevsky,et al.  Sintering anisotropy of binder jetted 316L stainless steel: part II – microstructure evolution during sintering , 2022, Powder Metallurgy.

[4]  A. Molinari,et al.  Effects of process parameters, debinding and sintering on the microstructure of 316L stainless steel produced by binder jetting , 2021, Materials Science and Engineering: A.

[5]  N. Lecis,et al.  Mechanical and microstructural characterization of WC-Co consolidated by binder jetting additive manufacturing , 2021 .

[6]  A. Gurlo,et al.  Characterization of powder flow behavior for additive manufacturing , 2021 .

[7]  A. Mostafaei,et al.  Influence of powder type and binder saturation on binder jet 3D–printed and sintered Inconel 625 samples , 2021, The International Journal of Advanced Manufacturing Technology.

[8]  N. Lecis,et al.  3D printing of fine alumina powders by binder jetting , 2021 .

[9]  E. Olevsky,et al.  Modeling of effect of powder spreading on green body dimensional accuracy in additive manufacturing by binder jetting , 2021 .

[10]  P. Trtik,et al.  Mapping Spatial Distribution of Pores in an Additively Manufactured Gold Alloy Using Neutron Microtomography , 2021, Applied Sciences.

[11]  Mark A. Atwater,et al.  Binder jetting additive manufacturing of copper foam structures , 2020 .

[12]  N. Baluc,et al.  Enhanced precipitate growth at reduced temperatures during chemical ordering in deformed red gold alloys , 2019, Scripta Materialia.

[13]  E. Toyserkani,et al.  Surface modification of binder-jet additive manufactured Inconel 625 via electrospark deposition , 2019, Surface and Coatings Technology.

[14]  A. Rollett,et al.  Real time observation of binder jetting printing process using high-speed X-ray imaging , 2019, Scientific Reports.

[15]  A. Mostafaei,et al.  Characterizing surface finish and fatigue behavior in binder-jet 3D-printed nickel-based superalloy 625 , 2018, Additive Manufacturing.

[16]  P. Kwon,et al.  Process development toward full-density stainless steel parts with binder jetting printing , 2017 .

[17]  M. Chi,et al.  Crystal Structural Effect of AuCu Alloy Nanoparticles on Catalytic CO Oxidation. , 2017, Journal of the American Chemical Society.

[18]  Dario Tiberto,et al.  Optimization of 18-karat yellow gold alloys for the additive manufacturing of jewelry and watch parts , 2017, Gold Bulletin.

[19]  Frank Cooper,et al.  Sintering and additive manufacturing: “additive manufacturing and the new paradigm for the jewellery manufacturer” , 2016 .

[20]  Mark A. Atwater,et al.  Solid‐State Foaming by Oxide Reduction and Expansion: Tailoring the Foamed Metal Microstructure in the Cu–CuO System with Oxide Content and Annealing Conditions , 2016 .

[21]  A. Tsai,et al.  Oxidation behavior and catalytic property of intermetallic compound AuCu , 2008 .

[22]  L. I. Kuznetsova,et al.  Kinetics and Mechanism of High-Temperature Oxidation in Air of Au - Cu Alloy , 2005 .

[23]  M. Lomello-Tafin,et al.  Preferential oxidation of CO in H2 over highly loaded Au/ZrO2 catalysts obtained by direct oxidation of bulk alloy. , 2005, Chemical communications.

[24]  G. Somorjai,et al.  Carbon monoxide oxidation over three different oxidation states of copper: Metallic copper, copper (I) oxide, and copper (II) oxide - a surface science and kinetic study , 1994 .

[25]  M. Grimwade.  The Metallurgy of Gold , 1992 .

[26]  J. Hausselt,et al.  Uses of Gold in Jewellery , 1992 .

[27]  E. A. Goldstein,et al.  Chemical kinetics of copper oxide reduction with carbon monoxide , 2011 .