Guidelines for etching silicon MEMS structures using fluorine high-density plasmas at cryogenic temperatures

This paper presents guidelines for the deep reactive ion etching (DRIE) of silicon MEMS structures, employing SF/sub 6//O/sub 2/-based high-density plasmas at cryogenic temperatures. Procedures of how to tune the equipment for optimal results with respect to etch rate and profile control are described. Profile control is a delicate balance between the respective etching and deposition rates of a SiO/sub x/F/sub y/ passivation layer on the sidewalls and bottom of an etched structure in relation to the silicon removal rate from unpassivated areas. Any parameter that affects the relative rates of these processes has an effect on profile control. The deposition of the SiO/sub x/F/sub y/ layer is mainly determined by the oxygen content in the SF/sub 6/ gas flow and the electrode temperature. Removal of the SiO/sub x/F/sub y/ layer is mainly determined by the kinetic energy (self-bias) of ions in the SF/sub 6//O/sub 2/ plasma. Diagrams for profile control are given as a function of parameter settings, employing the previously published "black silicon method". Parameter settings for high rate silicon bulk etching, and the etching of micro needles and micro moulds are discussed, which demonstrate the usefulness of the diagrams for optimal design of etched features. Furthermore, it is demonstrated that in order to use the oxygen flow as a control parameter for cryogenic DRIE, it is necessary to avoid or at least restrict the presence of fused silica as a dome material, because this material may release oxygen due to corrosion during operation of the plasma source. When inert dome materials like alumina are used, etching recipes can be defined for a broad variety of microstructures in the cryogenic temperature regime. Recipes with relatively low oxygen content (1-10% of the total gas volume) and ions with low kinetic energy can now be applied to observe a low lateral etch rate beneath the mask, and a high selectivity (more than 500) of silicon etching with respect to polymers and oxide mask materials is obtained. Crystallographic preference etching of silicon is observed at low wafer temperature (-120/spl deg/C). This effect is enhanced by increasing the process pressure above 10 mtorr or for low ion energies (below 20 eV).

[1]  Philippe Allongue,et al.  Etching of silicon in NaOH solutions. I: In-situ STM investigation of n-Si(111) , 1993 .

[2]  M. Allen,et al.  Micromachined needles for the transdermal delivery of drugs , 1998, Proceedings MEMS 98. IEEE. Eleventh Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Systems (Cat. No.98CH36176.

[3]  Miko Elwenspoek,et al.  The black silicon method: a universal method for determining the parameter setting of a fluorine-based reactive ion etcher in deep silicon trench etching with profile control , 1995 .

[4]  F. Mcfeely,et al.  Soft X-ray photoemission study of the silicon-fluorine etching reaction , 1986 .

[5]  High aspect ratio trench etching , 1996 .

[6]  E. V. D. Drift,et al.  Aspect ratio and crystallographic orientation dependence in deep dry silicon etching at cryogenic temperatures , 2001 .

[7]  G. Oehrlein,et al.  Surface processes in CF4/O2 reactive etching of silicon , 1988 .

[8]  W. Goedheer,et al.  Angular ion and neutral energy distribution in a collisional rf sheath , 1991 .

[9]  Low-Temperature Microwave Plasma Etching of Crystalline Silicon , 1991 .

[10]  Tony Zijlstra,et al.  Fabrication of two-dimensional photonic crystal waveguides for 1.5 μm in silicon by deep anisotropic dry etching , 1999 .

[11]  J. S. Danel,et al.  Deep and fast plasma etching for silicon micromachining , 1995 .

[12]  E. V. D. Drift,et al.  Kinetics and crystal orientation dependence in high aspect ratio silicon dry etching , 2000 .

[13]  Masayoshi Esashi,et al.  Silicon Micromachining , 1998, Digest of Papers. Microprocesses and Nanotechnology'98. 198 International Microprocesses and Nanotechnology Conference (Cat. No.98EX135).

[14]  Miko Elwenspoek,et al.  DEEMO: a new technology for the fabrication of microstructures , 1995, Proceedings IEEE Micro Electro Mechanical Systems. 1995.

[15]  F. Klemens,et al.  Comparison of advanced plasma sources for etching applications. V. Polysilicon etching rate, uniformity, profile control, and bulk plasma properties in a helical resonator plasma source , 1996 .

[16]  Kazunori Tsujimoto,et al.  Low‐temperature reactive ion etching and microwave plasma etching of silicon , 1988 .

[17]  J. Vance,et al.  Growth and Perfection of Crystals. , 1959 .

[18]  J. Coburn,et al.  Ion-enhanced gas-surface chemistry: The influence of the mass of the incident ion , 1981 .

[19]  Michael Curt Elwenspoek,et al.  The black silicon method. VIII. A study of the performance of etching silicon using SF6/O2-based chemistry with cryogenical wafer cooling and a high density ICP source , 1997 .

[20]  Hcw Herman Beijerinck,et al.  ION-ASSISTED SI/XEF2 ETCHING : TEMPERATURE DEPENDENCE IN THE RANGE 100-1000 K , 1996 .

[21]  J. Arnold,et al.  Charging of pattern features during plasma etching , 1991 .

[22]  Remco J. Wiegerink,et al.  RIE lag in high aspect ratio trench etching of silicon , 1997 .

[23]  Huma Ashraf,et al.  Advanced silicon etching using high-density plasmas , 1995, Photonics West - Micro and Nano Fabricated Electromechanical and Optical Components.

[24]  R. Wind,et al.  Macroscopic etch anisotropies and microscopic reaction mechanisms: a micromachined structure for the rapid assay of etchant anisotropy , 2000 .

[25]  Michael Curt Elwenspoek,et al.  On the Mechanism of Anisotropic Etching of Silicon , 1993 .

[26]  Reaction layer dynamics in silicon etching , 1995 .

[27]  Johann W. Bartha,et al.  Low temperature etching of Si in high density plasma using SF6/O2 , 1995 .