Fabrication of AlCoCrFeNi High-Entropy Alloy Coating on an AISI 304 Substrate via a CoFe2Ni Intermediate Layer

Through laser metal deposition, attempts were made to coat AlCoCrFeNi, a high-entropy alloy (HEA), on an AISI 304 stainless steel substrate to integrate their properties. However, the direct coating of the AlCoCrFeNi HEA on the AISI 304 substrate was found to be unviable due to cracks at the interface between these two materials. The difference in compositional change was suspected to be the source of the cracks. Therefore, a new transition route was performed by coating an intermediate layer of CoFe2Ni on the AISI 304 substrate. Investigations into the microstructure, phase composition, elemental composition and Vickers hardness were carried out in this study. Consistent metallurgical bonding was observed along both of the interfaces. It was found that the AlCoCrFeNi alloy solidified into a dendritic microstructure. The X-ray diffraction pattern revealed a transition of the crystal structure of the AISI 304 substrate to the AlCoCrFeNi HEA. An intermediate step in hardness was observed between the AISI 304 substrate and the AlCoCrFeNi HEA. The AlCoCrFeNi alloy fabricated was found to have an average hardness of 418 HV, while the CoFe2Ni intermediate layer had an average hardness of 275 HV.

[1]  B. Li,et al.  Microstructure and compressive properties of AlCrFeCoNi high entropy alloy , 2008 .

[2]  Hui Zhang,et al.  Synthesis and characterization of FeCoNiCrCu high-entropy alloy coating by laser cladding , 2011 .

[3]  A. F. Guillermet,et al.  Assessing the thermodynamics of the FeCONi system using a calphad predictive technique , 1989 .

[4]  Nannan Zhang,et al.  The Phase Evolution and Property of FeCoCrNiAlTix High-Entropy Alloying Coatings on Q253 via Laser Cladding , 2017 .

[5]  Andrew A. Shapiro,et al.  Development and characterization of Ti-6Al-4V to 304L stainless steel gradient components fabricated with laser deposition additive manufacturing , 2016 .

[6]  Hai-Lung Tsai,et al.  Additive manufacturing of Zr-based metallic glass structures on 304 stainless steel substrates via V/Ti/Zr intermediate layers , 2018, Materials Science and Engineering: A.

[7]  N. Frage,et al.  Heat treatment impacts the micro-structure and mechanical properties of AlCoCrFeNi high entropy alloy , 2016 .

[8]  Martin Löbel,et al.  Influence of Titanium on Microstructure, Phase Formation and Wear Behaviour of AlCoCrFeNiTix High-Entropy Alloy , 2018, Entropy.

[9]  Jien-Wei Yeh,et al.  Microstructure, thermophysical and electrical properties in AlxCoCrFeNi (0 ≤ x ≤2) high-entropy alloys , 2009 .

[10]  Muhammad Iqbal,et al.  Precipitation hardening in Inconel* 625 , 2000 .

[11]  Wei Li,et al.  Effects of tool path in remanufacturing cylindrical components by laser metal deposition , 2018, The International Journal of Advanced Manufacturing Technology.

[12]  Karen M. Taminger,et al.  Ti-Fe Intermetallics Analysis and Control in Joining Titanium Alloy and Stainless Steel by Laser Metal Deposition , 2017 .

[13]  Karin A. Dahmen,et al.  Aluminum Alloying Effects on Lattice Types, Microstructures, and Mechanical Behavior of High-Entropy Alloys Systems , 2013 .

[14]  Takahiko Kato,et al.  First demonstration of promising selective electron beam melting method for utilizing high-entropy alloys as engineering materials , 2015 .

[15]  Ming-Chuan Leu,et al.  Fabricating Functionally Graded Materials by Ceramic On-Demand Extrusion with Dynamic Mixing , 2018 .

[16]  L. W. Tsay,et al.  The effect of residual thermal stresses on the fatigue crack growth of laser-surface-annealed AISI 304 stainless steel: Part I: computer simulation , 2004 .

[17]  J. Yeh,et al.  Effects of Al addition on the microstructure and mechanical property of AlxCoCrFeNi high-entropy alloys , 2012 .

[18]  J. Yi,et al.  Synthesis and characterization of FeCoCrAlCu high-entropy alloy coating by laser surface alloying , 2015 .

[19]  U. Glatzel,et al.  Phase separation in equiatomic AlCoCrFeNi high-entropy alloy. , 2013, Ultramicroscopy.

[20]  Emilio Ramous,et al.  Influence of isothermal aging on secondary phases precipitation and toughness of a duplex stainless steel SAF 2205 , 2006 .

[21]  Kai Zhang,et al.  Evolution of microstructure, mechanical and corrosion properties of AlCoCrFeNi high-entropy alloy prepared by direct laser fabrication , 2017 .

[22]  Harihar Rakshit Sistla,et al.  Effect of Al/Ni ratio, heat treatment on phase transformations and microstructure of AlxFeCoCrNi2−x (x = 0.3, 1) high entropy alloys , 2015 .

[23]  Amit Gupta,et al.  Mechanical properties of Austenitic Stainless Steel 304L and 316L at elevated temperatures , 2016 .

[24]  Lin Li,et al.  Coincident wire and powder deposition by laser to form compositionally graded material , 2007 .

[25]  K. Dahmen,et al.  Microstructures and properties of high-entropy alloys , 2014 .

[26]  P. Liaw,et al.  Tensile ductility of an AlCoCrFeNi multi-phase high-entropy alloy through hot isostatic pressing (HIP) and homogenization , 2015 .

[27]  Frank W. Liou,et al.  Fabrication and Characterization of AlxCoFeNiCu1−x High Entropy Alloys by Laser Metal Deposition , 2017 .

[28]  Krzysztof J. Kurzydłowski,et al.  Microstructural characterisation of high-entropy alloy AlCoCrFeNi fabricated by laser engineered net shaping , 2015 .

[29]  Rui Vilar,et al.  Dry sliding wear behavior of laser clad TiVCrAlSi high entropy alloy coatings on Ti–6Al–4V substrate , 2012 .

[30]  Takahiko Kato,et al.  Relationship between the microstructure and mechanical properties of an equiatomic AlCoCrFeNi high-entropy alloy fabricated by selective electron beam melting , 2016 .

[31]  F. Elhalouani,et al.  The effect of cold work on structure and properties of AISI 304 stainless steel , 2008 .