Softening and melting mechanisms of polyamides interfering with sliding stability under adhesive conditions

Abstract The thermal stability of polymers is a main issue when used as friction elements under dry sliding. Cast polyamide grades processed with either natrium or magnesium catalysors are slid on a small-scale and a large-scale test configuration to reveal the effect of softening or degradation on the sliding stability and to investigate possibilities for extrapolation of friction and wear rates between both testing scales. The combination of softening and afterwards transition into the glassy state is detrimental for the sliding stability of natrium catalysed polyamides, characterised by heavy noise during sliding. A transfer film formed under continuous softening also provides high friction. Melting during initial sliding is necessary for stabilisation in both friction and wear, and eventual softening of a molten film near the end of the test then not deteriorates the sliding stability. Softening of magnesium catalysed polyamides is favourable for the formation of a coherent transfer film resulting in more stable sliding than natrium catalysed polyamides. The differences in softening mechanisms of both polyamide grades is correlated to structural changes investigated by thermal analysis and Raman spectroscopy: the γ crystalline structure prevails in magnesium catalysed samples and the α crystalline structure is predominant in natrium catalysed samples. For internal oil lubricated polyamides, a time dependent degradation of the polyamide bulk deteriorates the supply of internal oil lubricant to the sliding interface, resulting in high friction and wear under overload conditions. As the degradation mechanisms during sliding are strongly correlated to the test set-up, extrapolation is only possible for friction in a limited application range, while wear rates cannot be extrapolated.

[1]  D. Hull,et al.  The effect of polymerization conditions and crystallinity on the mechanical properties and fracture of spherulitic nylon 6 , 1975 .

[2]  Zygmunt Rymuza.  Energy concept of the coefficient of friction , 1996 .

[3]  Philippe Vergne,et al.  Analysis of oil supply phenomena by sintered porous reservoirs , 2001 .

[4]  K. Miyasaka,et al.  Effects of temperature and water on the γ → α crystalline transition of nylon 6 caused by stretching in the chain direction , 1968 .

[5]  J. Jakeš,et al.  Normal coordinate analyses of molecules with the amide group , 1971 .

[6]  T. Kanamoto,et al.  Effects of crystalline forms on the deformation behaviour of nylon-6 , 1998 .

[7]  Yoshitaka Uchiyama,et al.  Study on the formation of periodic ridges on the rubber surface by friction and wear monitoring , 2005 .

[8]  P. Baets,et al.  The tribological behaviour of engineering plastics during sliding friction investigated with small-scale specimens , 2002 .

[9]  B. Stuart.  The application of Raman spectroscopy to the tribology of polymers , 1998 .

[10]  D. Salem,et al.  FTIR spectroscopic characterization of structural changes in polyamide‐6 fibers during annealing and drawing , 2001 .

[11]  S. Kato,et al.  Lubricant-Supplying Properties and Durability of Oil-Impregnated Polymers , 2000 .

[12]  C. Bunn,et al.  The crystal structure of polycaproamide: Nylon 6 , 1955 .

[13]  B. Bhushan.  Principles and Applications of Tribology , 1999 .

[14]  M. Zhang,et al.  Friction induced mechanochemical and mechanophysical changes in high performance semicrystalline polymer , 1999 .

[15]  Francis E. Kennedy,et al.  Tribology of Plastic Materials , 1991 .

[16]  A. Argon,et al.  Rate Mechanism of Plasticity in the Crystalline Component of Semicrystalline Nylon 6 , 1994 .

[17]  H. Ishida,et al.  FTIR separation of nylon‐6 chain conformations: Clarification of the mesomorphous and γ‐crystalline phases , 1992 .

[18]  N. Murthy.  Metastable crystalline phases in nylon 6 , 1991 .

[19]  C. Depecker,et al.  Structural and mechanical behavior of nylon 6 films part I. Identification and stability of the crystalline phases , 2001 .

[20]  A. Argon,et al.  Deformation resistance in oriented nylon 6 , 1992 .

[21]  P. Colomban,et al.  Micro‐Raman study of the fatigue fracture and tensile behaviour of polyamide (PA 66) fibres , 2004 .

[22]  P. Baets,et al.  The friction and wear behaviour of polyamide 6 sliding against steel at low velocity under very high contact pressures , 1997 .

[23]  P. Baets,et al.  Sliding behaviour of pure polyester and polyester-PTFE filled bulk composites in overload conditions , 2005 .

[24]  L. Bark,et al.  Polymer changes during friction material performance , 1977 .

[25]  D. Walton,et al.  Measurement and Prediction of the Surface Temperature in Polymer Gears and Its Relationship to Gear Wear , 1993 .

[26]  P. Baets,et al.  Friction and wear of acetal: A matter of scale , 2005 .

[27]  J. S. Leendertz,et al.  Large-scale friction and wear tests on a hybrid UHMWPE-pad/primer coating combination used as bearing element in an extremely high-loaded ball-joint , 2006 .

[28]  H. Blok,et al.  The flash temperature concept , 1963 .

[29]  Study of the conformations of poly(ε-caprolactam) and poly(ε-caprolactam)-polybutadiene block copolymers by FT i.r. spectroscopy with photoacoustic detection and by micro-Raman confocal spectroscopy , 1997 .

[30]  A. Argon,et al.  Deconvolution of X-ray diffraction data to elucidate plastic deformation mechanisms in the uniaxial extension of bulk nylon 6 , 1991 .

[31]  D. Chung,et al.  The synthesis and frictional properties of lubricant-impregnated cast nylons , 2000 .

[32]  R. Séguéla,et al.  Structural and mechanical behavior of nylon‐6 films. II. Uniaxial and biaxial drawing , 2001 .

[33]  J. Laureyns,et al.  Structures and morphologies of cast and plastically strained polyamide 6 films as evidenced by confocal Raman microspectroscopy and atomic force microscopy , 2004 .