Heat treatment effect on the microstructure and corrosion behavior of 316L stainless steel fabricated by selective laser melting for proton exchange membrane fuel cells

Abstract Microstructure and corrosion behavior of 316L stainless steel fabricated by selective laser melting (SLM) for bipolar plate were investigated and the subsequent heat treatment effect was also clarified. Results showed that sub-grains widely existed in the SLM 316L and the dislocations in the grain boundary migrated and disappeared after heat treatment. The as produced SLM 316L exhibited inferior corrosion resistance than the wrought in 0.5 M H2SO4 solution with 50 ppm Cl− and 2 ppm F− ions at 70 °C due to the SLM defects (molten pool boundaries, non-equilibrium phases etc.), and short, stress relief annealing did not homogenize the non-uniform structures. However, recrystallization heat treatment can improve the durability due to the more uniform structure and thicker passive film. Meanwhile, the proportion of the oxides in passive film formed on SLM 316L increased after heat treatment, especially for the chromic oxide, leading to a better anti-corrosive property.

[1]  D. Kong,et al.  Long-Term Corrosion of Copper in Hot and Dry Atmosphere in Turpan, China , 2016, Journal of Materials Engineering and Performance.

[2]  X. Lou,et al.  On the stress corrosion crack growth behaviour in high temperature water of 316L stainless steel made by laser powder bed fusion additive manufacturing , 2017 .

[3]  Yusheng Shi,et al.  316L Stainless Steel with Gradient Porosity Fabricated by Selective Laser Melting , 2010 .

[4]  M. Terada,et al.  Investigation on the intergranular corrosion resistance of the AISI 316L(N) stainless steel after long time creep testing at 600 °C , 2008 .

[5]  H. Stone,et al.  Effect of heat treatment on the microstructure, texture and elastic anisotropy of the nickel-based superalloy CM247LC processed by selective laser melting , 2016 .

[6]  Artur Mateus,et al.  Predictive models for physical and mechanical properties of 316L stainless steel produced by selective laser melting , 2016 .

[7]  L. Neelakantan,et al.  Low-nickel austenitic stainless steel as an alternative to 316L bipolar plate for proton exchange membrane fuel cells , 2015 .

[8]  Jian Lu,et al.  Fatigue life improvement through surface nanostructuring of stainless steel by means of surface mechanical attrition treatment , 2006 .

[9]  Fu-hui Wang,et al.  The improvement of the corrosion resistance of 309 stainless steel in the transpassive region by nano-crystallization , 2009 .

[10]  J. Kubásek,et al.  Highly porous, low elastic modulus 316L stainless steel scaffold prepared by selective laser melting. , 2016, Materials science & engineering. C, Materials for biological applications.

[11]  Chaofang Dong,et al.  Bio-functional and anti-corrosive 3D printing 316L stainless steel fabricated by selective laser melting , 2018, Materials & Design.

[12]  M. Lima,et al.  Microstructure and mechanical behavior of laser additive manufactured AISI 316 stainless steel stringers , 2014 .

[13]  Hu Zhang,et al.  Selective laser melting of Al–8.5Fe–1.3V–1.7Si alloy: Investigation on the resultant microstructure and hardness , 2015 .

[14]  Wei Qingsong,et al.  Effect of molten pool boundaries on the mechanical properties of selective laser melting parts , 2014 .

[15]  D. Manfredi,et al.  Evaluation of corrosion resistance of Al–10Si–Mg alloy obtained by means of Direct Metal Laser Sintering , 2016 .

[16]  M. Golozar,et al.  The transpassive dissolution mechanism of 316L stainless steel , 2009 .

[17]  L. M. Kukreja,et al.  Studies on pitting corrosion and sensitization in laser rapid manufactured specimens of type 316L stainless steel , 2012 .

[18]  N. Birbilis,et al.  On the enhanced corrosion resistance of a selective laser melted austenitic stainless steel , 2017 .

[19]  C. Dong,et al.  Influence of pH on the passivation behaviour of 904L stainless steel bipolar plates for proton exchange membrane fuel cells , 2016 .

[20]  R. Schaller,et al.  Corrosion Properties of Powder Bed Fusion Additively Manufactured 17-4 PH Stainless Steel , 2017 .

[21]  Andrea R. Gerson,et al.  Resolving surface chemical states in XPS analysis of first row transition metals, oxides and hydroxides: Sc, Ti, V, Cu and Zn , 2010 .

[22]  K. Osakada,et al.  Rapid Manufacturing of Metal Components by Laser Forming , 2006 .

[23]  Hui Wang,et al.  Microstructure, defects and mechanical behavior of beta-type titanium porous structures manufactured by electron beam melting and selective laser melting , 2016 .

[24]  Lai‐Chang Zhang,et al.  Processing and properties of topologically optimised biomedical Ti-24Nb-4Zr-8Sn scaffolds manufactured by selective laser melting , 2015 .

[25]  Chor Yen Yap,et al.  Review of selective laser melting : materials and applications , 2015 .

[26]  Lai‐Chang Zhang,et al.  Heat Treatment Degrading the Corrosion Resistance of Selective Laser Melted Ti-6Al-4V Alloy , 2017 .

[27]  J. Humbeeck,et al.  Effect of heat treatment of 316L stainless steel produced by selective laser melting (SLM) , 2016 .

[28]  E. Akinlabi,et al.  Effect of crystallographic orientation on the pitting corrosion resistance of laser surface melted AISI 304L austenitic stainless steel , 2013 .

[29]  Zhen Chen,et al.  The AlSi10Mg samples produced by selective laser melting: single track, densification, microstructure and mechanical behavior , 2017 .

[30]  Suzhen Luo,et al.  Corrosion behavior of TiN coated type 316 stainless steel in simulated PEMFC environments , 2004 .

[31]  Zhaohui Huang,et al.  A selective laser melting and solution heat treatment refined Al-12Si alloy with a controllable ultrafine eutectic microstructure and 25% tensile ductility , 2015 .

[32]  C. Colin,et al.  Microstructural and mechanical approaches of the selective laser melting process applied to a nickel-base superalloy , 2012 .

[33]  M. Terada,et al.  Microstructure and intergranular corrosion of the austenitic stainless steel 1.4970 , 2006 .

[34]  Shing‐Jong Lin,et al.  Effect of surface oxide properties on corrosion resistance of 316L stainless steel for biomedical applications , 2004 .

[35]  U. Ramamurty,et al.  Mechanical behavior of selective laser melted 316L stainless steel , 2017 .

[36]  I. Olefjord,et al.  Passivation of Stainless Steels in Hydrochloric Acid , 1999 .

[37]  C. Dong,et al.  Passivation and electrochemical behavior of 316L stainless steel in chlorinated simulated concrete pore solution , 2017 .

[38]  R. Kelly,et al.  Unexpected Interface Corrosion and Sensitization Susceptibility in Additively Manufactured Austenitic Stainless Steel , 2018 .

[39]  Shahram Karimi,et al.  A Review of Metallic Bipolar Plates for Proton Exchange Membrane Fuel Cells: Materials and Fabrication Methods , 2012 .

[40]  Johann Sienz,et al.  Investigation into the effect of process parameters on microstructural and physical properties of 316L stainless steel parts by selective laser melting , 2014, The International Journal of Advanced Manufacturing Technology.

[41]  E. Otero,et al.  Corrosion behaviour of aisi 304l and 316l stainless steels prepared by powder metallurgy in the presence of sulphuric and phosphoric acid , 1998 .

[42]  Shuqi Zheng,et al.  Mechanism of (Mg, Al, Ca)-oxide inclusion-induced pitting corrosion in 316L stainless steel exposed to sulphur environments containing chloride ion , 2013 .

[43]  L. Froyen,et al.  Selective laser melting of iron-based powder , 2004 .

[44]  M. Ziętala,et al.  The microstructure, mechanical properties and corrosion resistance of 316 L stainless steel fabricated using laser engineered net shaping , 2016 .

[45]  Dong-bai Sun,et al.  The passive oxide films growth on 316L stainless steel in borate buffer solution measured by real-time spectroscopic ellipsometry , 2015 .

[46]  C. Dong,et al.  Effect of cold deformation on the electrochemical behaviour of 304L stainless steel in contaminated sulfuric acid environment , 2017 .

[47]  T. Yue,et al.  The effect of excimer laser surface treatment on pitting corrosion resistance of 316LS stainless steel , 2001 .

[48]  K. Vanmeensel,et al.  Corrosion Testing of a Heat Treated 316 L Functional Part Produced by Selective Laser Melting , 2017 .

[49]  L. P. Karjalainen,et al.  Understanding the impact of grain structure in austenitic stainless steel from a nanograined regime to a coarse-grained regime on osteoblast functions using a novel metal deformation-annealing sequence. , 2013, Acta biomaterialia.

[50]  Markus Bambach,et al.  Study of the effect of heat treatment on fatigue crack growth behaviour of 316L stainless steel produced by selective laser melting , 2018 .

[51]  P. Peyre,et al.  Influence of high power diode laser surface melting on the pitting corrosion resistance of type 316L stainless steel , 2002 .

[52]  N. Birbilis,et al.  On the corrosion and metastable pitting characteristics of 316L stainless steel produced by selective laser melting , 2017 .

[53]  Lucas Dembinski,et al.  The study of the laser parameters and environment variables effect on mechanical properties of high compact parts elaborated by selective laser melting 316L powder , 2013 .

[54]  Xuanhui Qu,et al.  Structural and mechanical characteristics of porous 316L stainless steel fabricated by indirect selective laser sintering , 2013 .

[55]  Y. Zhong,et al.  Hardened austenite steel with columnar sub-grain structure formed by laser melting , 2015 .

[56]  M. Nakada,et al.  Inclusion Particle Growth during Solidification of Stainless Steel , 2001 .

[57]  A. Röttger,et al.  Corrosion behavior of 316L austenitic steel processed by selective laser melting, hot‐isostatic pressing, and casting , 2017 .

[58]  C. Dong,et al.  Improved pitting corrosion resistance of AISI 316L stainless steel treated by high current pulsed electron beam , 2006 .

[59]  Suyitno,et al.  Effect of surface mechanical attrition treatment (SMAT) on microhardness, surface roughness and wettability of AISI 316L , 2011 .

[60]  M. Azam,et al.  Formation of Cr23C6 during the Sensitization of AISI 304 Stainless Steel and its Effect to Pitting Corrosion , 2012, International Journal of Electrochemical Science.

[61]  R. A. Antunes,et al.  Corrosion of metal bipolar plates for PEM fuel cells: A review , 2010 .

[62]  K. Edström,et al.  Corrosion resistances and passivation of powder metallurgical and conventionally cast 316L and 2205 stainless steels , 2013 .

[63]  Yifu Shen,et al.  Balling phenomena in direct laser sintering of stainless steel powder: Metallurgical mechanisms and control methods , 2009 .

[64]  C. Dong,et al.  Interaction between austein-ferrite phases on passive performance of 2205 duplex stainless steel , 2018, Journal of Materials Science & Technology.

[65]  S. Suresh Babu,et al.  Additive manufactured bipolar plate for high-efficiency hydrogen production in proton exchange membrane electrolyzer cells , 2017 .

[66]  M. Mazinani,et al.  Effect of grain size on pitting corrosion of 304L austenitic stainless steel , 2015 .