Constructal design and optimization of a direct contact humidification–dehumidification desalination unit

Abstract This study shows that the main design features of a direct contact humidification–dehumidification (HD) desalination process can be determined based on the method of the constructal design. A direct contact HD unit has three main sections: the humidifier, the dehumidifier and the heat source. To analyze and optimize such unit, two flow models for air circulation are considered: natural and forced circulations. The objective is increasing the water production rate over the volume occupied by the plant. The parameters considered in this work are the air flow rate, tube diameters ratio, temperatures and flow rates of inlet saline and fresh water. The Lagrangian multipliers and genetic algorithm (GA) methods are used to optimize the production rate subject to global constraint (fixed volume). The constructal design developed in this paper explains the influences of the inlet cold and hot water temperatures and air flow rate on the basic design parameters of HD system architecture. It shows that the optimal configuration of HD system is consequently temperature dependent. Finally, the analysis shows that if the humidifier inlet water temperature is high, recycling of the humidifier outlet water results in about 15–25% reduction in the specific thermal energy consumption.

[1]  Adrian Bejan,et al.  Integral measures of electric power distribution networks: load–length curves and line-network multipliers , 2003 .

[2]  Y. Azoumah,et al.  Constructal network for heat and mass transfer in a solid–gas reactive porous medium , 2004 .

[3]  Mohammad Sadegh Hatamipour,et al.  Mathematical modeling of a direct contact humidification–dehumidification desalination process , 2009 .

[4]  Majid Amidpour,et al.  Constructal design of humidification–dehumidification desalination unit architecture , 2011 .

[5]  Majid Amidpour,et al.  Derivation of optimal geometry of a multi-effect humidification–dehumidification desalination unit: A constructal design , 2011 .

[6]  A. H. Reis,et al.  Constructal theory of global circulation and climate , 2006 .

[7]  Antonio F. Miguel,et al.  Constructal design of solar energy-based systems for buildings , 2008 .

[8]  Adrian Bejan,et al.  Steam generator structure: Continuous model and constructal design , 2011 .

[9]  Adrian Bejan,et al.  Design with constructal theory , 2008 .

[10]  Mohammed M. Farid,et al.  Solar desalination based on humidification process—II. Computer simulation , 1999 .

[11]  Adrian Bejan,et al.  Constructal steam generator architecture , 2009 .

[12]  Majid Amidpour,et al.  Performance optimization of the humidification–dehumidification desalination process using mathematical programming , 2009 .

[13]  Luiz Alberto Oliveira Rocha,et al.  Constructal design of T–Y assembly of fins for an optimized heat removal , 2009 .

[14]  Reza Azin,et al.  New experimental aspects of the carrier gas process (CGP) , 2004 .

[15]  Palanichamy Gandhidasan.  Prediction of pressure drop in a packed bed dehumidifier operating with liquid desiccant , 2002 .

[16]  Hefei Zhang,et al.  Performance optimization of solar humidification–dehumidification desalination process using Pinch technology , 2005 .

[17]  A. Bejan,et al.  Unifying constructal theory for scale effects in running, swimming and flying , 2006, Journal of Experimental Biology.

[18]  Y. Muzychka.  Constructal multi-scale design of compact micro-tube heat sinks and heat exchangers , 2007 .

[19]  Majid Amidpour,et al.  Cost optimization of a solar humidification-dehumidification desalination unit using mathematical programming , 2009 .

[20]  Jing Fan,et al.  Constructal design of nanofluids , 2010 .

[21]  Hisham Ettouney,et al.  Humidification dehumidification desalination process: Design and performance evaluation , 2008 .

[22]  Adrian Bejan,et al.  Constructal tree shaped networks for the distribution of electrical power , 2003 .

[23]  A. Bejan,et al.  Constructal solar chimney configuration , 2010 .

[24]  Hisham Ettouney,et al.  Design and analysis of humidification dehumidification desalination process , 2005 .

[25]  Adrian Bejan,et al.  Dendritic constructal heat exchanger with small-scale crossflows and larger-scales counterflows , 2002 .

[26]  Adrian Bejan,et al.  Designed porous media: maximal heat transfer density at decreasing length scales , 2004 .

[27]  Guofeng Yuan,et al.  Mathematical modeling of a closed circulation solar desalination unit with humidification-dehumidification , 2007 .

[28]  Fengrui Sun,et al.  Heat-conduction optimization based on constructal theory , 2007 .

[29]  A. Ravindran,et al.  Engineering Optimization: Methods and Applications , 2006 .

[30]  J. R. Selman,et al.  Solar desalination with a humidification-dehumidification cycle: mathematical modeling of the unit , 2003 .

[31]  A. V. Azad,et al.  Economic Optimization of Shell and Tube Heat Exchanger Based on Constructal Theory , 2011 .

[32]  M. Engelhardt,et al.  Small-scale thermal seawater desalination simulation and optimization of system design , 1999 .

[33]  Richard Edwin Sonntag,et al.  Fundamentals of Thermodynamics , 1998 .

[34]  Mohammad Sadegh Hatamipour,et al.  Economical study of a small-scale direct contact humidification–dehumidification desalination plant , 2010 .

[35]  James R. Fair,et al.  General model for prediction of pressure drop and capacity of countercurrent gas/liquid packed columns , 1989 .

[36]  Adrian Bejan,et al.  Streets tree networks and urban growth: Optimal geometry for quickest access between a finite-size volume and one point , 1998 .