Effect of Processing Parameters on the Mechanical Properties of Injection Molded Thermoplastic Polyolefin (TPO) Cellular Foams

In this study, the effects of processing parameters on the mechanical properties of injection molded thermoplastic polyolefin (TPO) foams are investigated. Closed cell TPO foams were prepared by injection molding process. The microstructure of these foamed samples was controlled by carefully altering the processing parameters on the injection molding machine. The foam morphologies were characterized in terms of skin thickness, surface roughness, and relative foam density. Tensile properties and impact resistance of various injection molded TPO samples were correlated with various foam morphologies. The findings show that the mechanical properties are significantly affected by foam morphologies. The experimental results obtained from this study can be used to predict the microstructure and mechanical properties of cellular injection molded TPO foams prepared with different processing parameters.

[1]  Donald R Paul,et al.  TPO based nanocomposites. Part 1. Morphology and mechanical properties , 2005 .

[2]  Jin Fu,et al.  Effect of Processing Parameters on Cellular Structures and Mechanical Properties of PMMA Microcellular Foams , 2005 .

[3]  J. K. Mishra,et al.  Preparation, mechanical and rheological properties of a thermoplastic polyolefin (TPO)/organoclay nanocomposite with reference to the effect of maleic anhydride modified polypropylene as a compatibilizer , 2005 .

[4]  M. Champagne,et al.  Impact-Compression-Morphology Relationship in Polyolefin Foams , 2005 .

[5]  F. Mirabella,et al.  Thermoplastic olefin/clay nanocomposites: Morphology and mechanical properties , 2004 .

[6]  E. Archer,et al.  Processing characteristics and mechanical properties of metallocene catalyzed linear low-density polyethylene foams for rotational molding , 2004 .

[7]  Hyunchul Jung,et al.  Mechanical, morphological, and thermal properties of rigid polyurethane foams blown by distilled water , 2003 .

[8]  J. E. Mark,et al.  Preparation, characterization, and mechanical properties of some microcellular polysulfone foams , 2002 .

[9]  Kenji Hikita,et al.  Development of weight reduction technology for door trim using foamed PP , 2002 .

[10]  J. Lu,et al.  Toughening mechanisms in commercial thermoplastic polyolefin blends , 2000 .

[11]  C. Papadopoulou,et al.  Comparison of compatibilizer effectiveness for PET/PP blends: their mechanical, thermal and morphology characterization , 2000 .

[12]  Chul B. Park,et al.  Cell morphology and property relationships of microcellular foamed pvc/wood‐fiber composites , 1998 .

[13]  D. Baird,et al.  Impact behavior of microcellular foams of polystyrene and styrene‐acrylonitrile copolymer, and single‐edge‐notched tensile toughness of microcellular foams of polystyrene, styrene‐acrylonitrile copolymer, and palycarbonate , 1995 .

[14]  Karl A. Seeler,et al.  Experimental Characterization of the Tensile Behavior of Microcellular Polycarbonate Foams , 1994 .

[15]  J. E. Mark,et al.  The effect of preloading on the mechanical properties of polymeric foams , 1994 .

[16]  P. R. Stupak,et al.  The Effect of Bead Fusion on the Energy Absorption of Polystyrene Foam. Part II: Energy Absorption , 1991 .

[17]  L. Hornberger,et al.  EVALUATING MECHANICAL PROPERTIES OF REINFORCED PC STRUCTURAL FOAM , 1991 .

[18]  D. A. Ysseldyke,et al.  Mechanical properties of rigid thermoplastic foams—Part II: Stiffness and strength data for modified polyphenylene oxide foams , 1988 .