Spark Plasma Sintering and Characterization of Al-TiB2 Composites

In this study, Al-TiB2 compacts fabricated by spark plasma sintering methods at different temperatures were characterized for densification, microstructural development, and mechanical properties. Sintering parameters used were temperatures of 500 °C and 550 °C under the pressure of 30 MPa. A very dense microstructure with uniform phase distribution and porosity was produced in the sample sintered at 550 °C with 2.5 wt% TiB2. The same sample exhibited excellent hardness value, and a high-tensile strength attributed to full metallurgical bonding, presence of sub-micron sized grains, and their uniform distribution. These results show that the TiB2 addition enhanced the composite’s hardness, sintered density, and tensile strength. In all the sintered samples, the fractographs revealed a mixed-mode fracture (ductile and brittle).

[1]  B. Mittelman,et al.  Cold Forming of Al-TiB2 Composites Fabricated by SPS: A Computational Experimental Study , 2020, Materials.

[2]  Ronald A. Kohser,et al.  DeGarmo's Materials and Processes in Manufacturing , 2020 .

[3]  N. K. Babu,et al.  Mechanical and tribological characterization of aluminum metal matrix composite reinforced with micro ceramic particles (TiB2/SiC) , 2020 .

[4]  H. Shahrajabian,et al.  Mechanical properties and microstructure of Al/(TiC+TiB2) composite fabricated by spark plasma sintering , 2019, Ceramics International.

[5]  G. Gupta,et al.  Effect of matrix powder and reinforcement content on tribological behavior of particulate 6061Al-TiB2 composites , 2018, Journal of Composite Materials.

[6]  R. Singh,et al.  Synthesis, Consolidation and Modelling Study of AA2014-TiB2 Composite Prepared by Powder Metallurgy (P/M) Method , 2018, Materials Science Forum.

[7]  S. Prabu,et al.  Combined effect of process parameters during aluminothermic reaction process on the microstructure and mechanical properties of in situ Al/TiB 2 composite , 2018 .

[8]  S. Prabu,et al.  Wear Behaviour of In Situ Al/TiB2 Composite: Influence of the Microstructural Instability , 2018, Tribology Letters.

[9]  S. Sivananthan,et al.  INVESTIGATION OF MECHANICAL PROPERTIES FOR Al-SiC-TiB2 METAL MATRIX COMPOSITE , 2018 .

[10]  D. Fu,et al.  Fabrication of aluminium matrix hybrid composites reinforced with SiC microparticles and TiB2 nanoparticles by powder metallurgy , 2017 .

[11]  Z. Sadeghian,et al.  Role of powder preparation route on microstructure and mechanical properties of Al-TiB2 composites fabricated by accumulative roll bonding (ARB) , 2016 .

[12]  Z. Sadeghian,et al.  Investigating the microstructure and mechanical properties of Al-TiB2 composite fabricated by Friction Stir Processing (FSP) , 2016 .

[13]  E. Ghasali,et al.  Mechanical properties and microstructure characterization of spark plasma and conventional sintering of Al–SiC–TiC composites , 2016 .

[14]  R. S. Maurya,et al.  Al Alloy Nanocomposite Reinforced with Physically Functionalized Carbon Nanotubes Synthesized via Spark Plasma Sintering , 2016 .

[15]  Hamid Khayyam,et al.  Effect of B4C, TiB2 and ZrSiO4 ceramic particles on mechanical properties of aluminium matrix composites: Experimental investigation and predictive modelling , 2016 .

[16]  Hamid Khayyam,et al.  Boron carbide reinforced aluminium matrix composite: Physical, mechanical characterization and mathematical modelling , 2016 .

[17]  Haidong Zhao,et al.  Effects of Manufacturing Processes on Microstructure and Properties of Al/A356–B4C Composites , 2016 .

[18]  L. Chen,et al.  B4C/Al Composites Processed by Metal-assisted Pressureless Infiltration Technique and its Characterization , 2016 .

[19]  K. Asano.  Preparation of Alumina Fiber-Reinforced Aluminum by Squeeze Casting and Their Machinability , 2015 .

[20]  A. R. Daud,et al.  Chemical composition, microstructure and sintering temperature modifications on mechanical properties of TiC-based cermet – A review , 2015 .

[21]  Tongmin Wang,et al.  TiB2 reinforced aluminum based in situ composites fabricated by stir casting , 2015 .

[22]  A. Evangelou,et al.  Aluminium reinforced by WC and TiC nanoparticles (ex-situ) and aluminide particles (in-situ): Microstructure, wear and corrosion behaviour , 2015 .

[23]  M. A. Baghchesara,et al.  Production and microstructural investigation of Al-nano TiB2 composite produced by powder metallurgy technique , 2014 .

[24]  S. Suresh,et al.  Tribological and Mechanical Behavior Study of Al6061-TiB2 Metal Matrix Composites Using Stir Casting , 2014 .

[25]  S. C. Vettivel,et al.  Mechanical behavior and wear prediction of stir cast Al–TiB2 composites using response surface methodology , 2014 .

[26]  Y. Zhang,et al.  Microstructure and mechanical properties of TiB2/2219 composites , 2014 .

[27]  O. Guillon,et al.  Field‐Assisted Sintering Technology/Spark Plasma Sintering: Mechanisms, Materials, and Technology Developments , 2014 .

[28]  M. Vedani,et al.  Metal Matrix Composites Reinforced by Nano-Particles—A Review , 2014 .

[29]  R. Ramanujam,et al.  Hybrid Aluminium Metal Matrix Composite Reinforced with SiC and TiB2 , 2014 .

[30]  S. Suresh,et al.  Production and Characterization of Al 6061- TiB2 Metal Matrix Composites , 2013 .

[31]  Adolfo Fernández,et al.  Challenges and Opportunities for Spark Plasma Sintering: A Key Technology for a New Generation of Materials , 2013 .

[32]  N. Saheb.  Spark plasma and microwave sintering of Al6061 and Al2124 alloys , 2013, International Journal of Minerals, Metallurgy, and Materials.

[33]  H. Abdizadeh,et al.  DENSIFICATION AND MECHANICAL PROPERTIES OF TiB2-SiC NANOCOMPOSITE WITH SILICON CARBAID AS A SINTERING AID , 2012 .

[34]  H. Abdizadeh,et al.  Improvement in physical and mechanical properties of aluminum/zircon composites fabricated by powder metallurgy method , 2011 .

[35]  Z. Sadeghian,et al.  Microstructural and mechanical evaluation of Al-TiB2 nanostructured composite fabricated by mechanical alloying , 2011 .

[36]  R. Keshavamurthy,et al.  A study on microstructure and mechanical properties of Al 6061–TiB2 in-situ composites , 2011 .

[37]  Z. Sadeghian,et al.  Characterisation of in situ Al–TiB2 nanocomposite powder synthesised by mechanical alloying , 2011 .

[38]  S. Natarajan,et al.  Synthesis and evaluation of mechanical and high temperature tribological properties of in-situ Al-TiC composites , 2010 .

[39]  Ahmet Karaaslan,et al.  Processing and microstructural characterisation of AA 1070 and AA 6063 matrix B4Cp reinforced composites , 2010 .

[40]  Jun Wang,et al.  Microstructural characterization and mechanical properties of TiAl–Al2Ti4C2–Al2O3–TiC in situ composites by hot-press-aided reaction synthesis , 2006 .

[41]  C. Hwang,et al.  Densification and mechanical properties of titanium diboride with silicon nitride as a sintering aid , 2004 .

[42]  V. Arunachalam,et al.  Effect of particle inclusions on the mechanical properties of composites fabricated by liquid metallurgy , 2003 .

[43]  J. Torralba,et al.  P/M aluminum matrix composites: an overview , 2003 .

[44]  F. Weng,et al.  In situ reacted titanium nitride-reinforced aluminum alloy composite , 2002 .

[45]  C. F. Feng,et al.  In situ TiB2 reinforced Al alloy composites , 2001 .

[46]  J. W. Kaczmar,et al.  The production and application of metal matrix composite materials , 2000 .

[47]  R. Munro.  Material Properties of Titanium Diboride , 2000, Journal of research of the National Institute of Standards and Technology.

[48]  S. Torizuka,et al.  Effect of SiC on Interfacial Reaction and Sintering Mechanism of TiB2 , 1995 .

[49]  P. Tsakiropoulos,et al.  Characterisation of spatial distribution of reinforcement in powder metallurgy route Al/SiCp metal matrix composites , 1995 .

[50]  J. H. Rendall,et al.  Powder Metallurgy , 1961, Nature.