Improvement of chatter stability in boring operations with passive vibration absorbers

Abstract This paper is focused on the behavior of boring bars with a passive dynamic vibration absorber (DVA) for chatter suppression. The boring bar was modeled as a cantilever Euler–Bernoulli beam and only its first mode of vibration was considered. The stability of the two-degree-of-freedom model was analyzed constructing the stability diagram, dependent on the bar characteristics and on the absorber parameters (mass, stiffness, damping, and position). Two analytical approaches for tuning the absorber parameters were compared. The selection criterion consisted on the maximization of the minimum values of the stability-lobes diagram. Subsequent analysis performed in this work, allowed formulating of new analytical expressions for the tuning frequency improving the behavior of the system against chatter.

[1]  Y. S. Tarng,et al.  Design of a dynamic vibration absorber against vibrations in turning operations , 2001 .

[2]  Etsuo Marui,et al.  Suppression of chatter vibration of boring tools using impact dampers , 2000 .

[3]  Ali H. Nayfeh,et al.  Chatter control and stability analysis of a cantilever boring bar under regenerative cutting conditions , 2001, Philosophical Transactions of the Royal Society of London. Series A: Mathematical, Physical and Engineering Sciences.

[4]  Erhan Budak,et al.  Analytical Modeling of Chatter Stability in Turning and Boring Operations—Part I: Model Development , 2007 .

[5]  B. Moetakef-Imani,et al.  Dynamic simulation of boring process , 2009 .

[6]  Yusuf Altintas,et al.  Analytical Prediction of Chatter Stability in Milling—Part II: Application of the General Formulation to Common Milling Systems , 1998 .

[7]  Zichen Chen,et al.  Magnetorheological fluid-controlled boring bar for chatter suppression , 2009 .

[8]  Lars Håkansson,et al.  Identification of dynamic properties of boring bar vibrations in a continuous boring operation , 2004 .

[9]  P. N. Rao,et al.  Towards improved design of boring bars part 1: Dynamic cutting force model with continuous system analysis for the boring bar performance , 1988 .

[10]  Juan Carlos Jáuregui-Correa,et al.  Analysis of compliance between the cutting tool and the workpiece on the stability of a turning process , 2008 .

[11]  C. Mei,et al.  Active regenerative chatter suppression during boring manufacturing process , 2005 .

[12]  Yusuf Altintas,et al.  Dynamics of boring processes: Part III-time domain modeling , 2002 .

[13]  Tatiana Smirnova,et al.  Analysis of dynamic properties of boring bars concerning different clamping conditions , 2009 .

[14]  S. A. Tobias.  Machine-tool vibration , 1965 .

[15]  Gábor Stépán,et al.  Stability of High-Speed Milling , 2000, Nonlinear Dynamics and Stochastic Mechanics.

[16]  Sanjiv G. Tewani,et al.  A study of cutting process stability of a boring bar with active dynamic absorber , 1995 .

[17]  Chun Liu,et al.  An Analytical Model of Cutting Dynamics. Part 1: Model Building , 1985 .

[18]  D. W. Wu,et al.  An Analytical Model of Cutting Dynamics. Part 2: Verification , 1985 .

[19]  P. E. Gygax,et al.  Cutting Dynamics and Stability of Boring Bars , 1990 .

[20]  S. A. Tobias,et al.  A Theory of Nonlinear Regenerative Chatter , 1974 .

[21]  G. M. Zhang,et al.  DYNAMIC MODELING AND ANALYSIS OF THE BORING MACHINING SYSTEM. , 1985 .

[22]  R N Arnold,et al.  Cutting Tools Research: Report of Subcommittee on Carbide Tools: The Mechanism of Tool Vibration in the Cutting of Steel , 1946 .

[23]  E. W. Parker,et al.  Dynamic Stability of a Cantilever Boring Bar with Machined Flats under Regenerative Cutting Conditions , 1970 .

[24]  Graeme Manson,et al.  Fuzzy stability analysis of regenerative chatter in milling , 2010 .

[25]  Tatiana Smirnova,et al.  On the Development of a Simple and Robust Active Control System for Boring Bar Vibration in Industry , 2007 .

[26]  Yusuf Altintas,et al.  Analytical Prediction of Chatter Stability in Milling—Part I: General Formulation , 1998 .

[27]  Eugene Rivin,et al.  Enhancement of dynamic stability of cantilever tooling structures , 1992 .

[28]  Emre Özlü,et al.  Analytical modeling of chatter stability in turning and boring operations-Part II: Experimental verification , 2007 .

[29]  Min Wang,et al.  Chatter suppression based on nonlinear vibration characteristic of electrorheological fluids , 1999 .

[30]  Jon Rigelsford,et al.  Manufacturing Automation: Metal Cutting Mechanics, Machine Tool Vibrations, and CNC Design , 2004 .

[31]  H. E. Merritt.  Theory of Self-Excited Machine-Tool Chatter: Contribution to Machine-Tool Chatter Research—1 , 1965 .

[32]  Tony L. Schmitz,et al.  Effects of Radial Immersion and Cutting Direction on Chatter Instability in End-Milling , 2002 .

[33]  Hamed Moradi,et al.  Tuneable vibration absorber design to suppress vibrations: An application in boring manufacturing process , 2008 .

[34]  Lars Håkansson,et al.  Identification of motion of cutting tool vibration in a continuous boring operation-correlation to structural properties , 2004 .

[35]  Y. S. Tarng,et al.  Chatter suppression in turning operations with a tuned vibration absorber , 2000 .

[36]  J. Saffury,et al.  Optimized chatter resistance of viscoelastic turning bars , 2009 .

[37]  Neil D. Sims,et al.  Vibration absorbers for chatter suppression: A new analytical tuning methodology , 2007 .

[38]  F. W. Taylor.  The Art of Cutting Metals , 1907 .