Microstructure evolution and nano-phases strengthening of Al-5%Cu alloy by adding trace AlSiTiCrNiCu high entropy alloy

[1]  Y. Lin,et al.  Microstructure and mechanical properties in the TLP joint of FeCoNiTiAl and Inconel 718 alloys using BNi2 filler , 2021 .

[2]  T. Xia,et al.  Effects of AlCoCrFeNiTi high-entropy alloy on microstructure and mechanical properties of pure aluminum , 2020 .

[3]  T. Xia,et al.  Effect of scandium addition on microstructure and mechanical properties of as-cast Al-5%Cu alloys , 2020 .

[4]  Amauri Garcia,et al.  The effects of Cr addition on microstructure, hardness and tensile properties of as-cast Al–3.8wt.%Cu–(Cr) alloys , 2020 .

[5]  Q. Gu,et al.  Insight into Si poisoning on grain refinement of Al-Si/Al-5Ti-B system , 2020 .

[6]  V. Cheverikin,et al.  An experimental investigation of phase transformations in the Al-rich corner of the Al–Cr–Fe system , 2019, Journal of Alloys and Compounds.

[7]  Q. Cai,et al.  Microstructure and properties of as-cast Al-4.5Cu-1.5Mg alloy refined with Ti-supported TiC nanoparticles via ultrasonic-assisted addition , 2019, Materials Science and Engineering: A.

[8]  T. Xia,et al.  A novel modifier on the microstructure and mechanical properties of Al-7Si alloys , 2019, Materials Letters.

[9]  L.F. Cao,et al.  Co-stabilization of θ′-Al2Cu and Al3Sc precipitates in Sc-microalloyed Al–Cu alloy with enhanced creep resistance , 2019, Materials Today Nano.

[10]  Kun Liu,et al.  Influence of the modification of iron-bearing intermetallic and eutectic Si on the mechanical behavior near the solidus temperature in Al-Si-Cu 319 cast alloy , 2019, Physica B: Condensed Matter.

[11]  L. Salvo,et al.  In situ nanotomography study of creep cavities in Al-3.6-Cu alloy , 2019, Acta Materialia.

[12]  M. Schöbel,et al.  Elasto-plastic deformation in Al-Cu cast alloys for engine components , 2019, Journal of Alloys and Compounds.

[13]  Xiangfa Liu,et al.  Enhanced age-hardening behavior in Al–Cu alloys induced by in-situ synthesized TiC nanoparticles , 2019, Journal of Materials Science & Technology.

[14]  Zhiwei Liu,et al.  On the preparation and mechanical properties of in situ small-sized TiB2/Al-4.5Cu composites via ultrasound assisted RD method , 2018, Journal of Alloys and Compounds.

[15]  Bin-hao Hu,et al.  Analyzing the microstructural evolution and hardening response of an Al-Si-Mg casting alloy with Cr addition , 2018, Materials Characterization.

[16]  Y. Wang,et al.  The mechanistic contribution of nanosized Al3Fe phase on the mechanical properties of Al-Fe alloy , 2018 .

[17]  J. Kuang,et al.  Grain size-dependent Sc microalloying effect on the yield strength-pitting corrosion correlation in Al-Cu alloys , 2018 .

[18]  F. Qiu,et al.  Simultaneously increasing the high-temperature tensile strength and ductility of nano-sized TiCp reinforced Al-Cu matrix composites , 2018 .

[19]  M. Qian,et al.  Grain refinement of binary Al-Si, Al-Cu and Al-Ni alloys by ultrasonication , 2017 .

[20]  S. Bajpai,et al.  Effect of semi-solid forging on microstructure and mechanical properties of in-situ cast Al-Cu-TiB2 composites , 2017 .

[21]  F. Qiu,et al.  Superior creep resistance of 0.3 wt% nano-sized TiCp/Al-Cu composite , 2017 .

[22]  I. Golovin,et al.  Effect of homogenisation treatment on precipitation, recrystallisation and properties of Al – 3% Mg – TM alloys (TM = Mn, Cr, Zr) , 2016 .

[23]  J. H. Chen,et al.  Mechanical properties enhanced by deformation-modified precipitation of θ′-phase approximants in an Al-Cu alloy , 2016 .

[24]  D. Seidman,et al.  Mechanical properties and optimization of the aging of a dilute Al-Sc-Er-Zr-Si alloy with a high Zr/Sc ratio , 2016 .

[25]  B. Abbey,et al.  Strengthening mechanisms in an Al-Fe-Cr-Ti nano-quasicrystalline alloy and composites , 2016 .

[26]  Q. Jiang,et al.  Grain refinement behavior of Al–Cu alloys inoculated by various metallic glasses , 2015 .

[27]  Hao-wei Wang,et al.  Effect of Cr content and heat-treatment on the high temperature strength of eutectic Al–Si alloys , 2015 .

[28]  Biao Chen,et al.  Length-scale dependent microalloying effects on precipitation behaviors and mechanical properties of Al–Cu alloys with minor Sc addition , 2015 .

[29]  X. Li,et al.  Microstructure and crystal growth direction of Al–Cu alloy , 2015 .

[30]  Kyu C. Cho,et al.  Prediction models for the yield strength of particle-reinforced unimodal pure magnesium (Mg) metal matrix nanocomposites (MMNCs) , 2013, Journal of Materials Science.

[31]  Jing Zhang,et al.  Effect of fine-grained raw material addition on microstructure refinement and tensile properties in horizontal continuous casting Al–12%Si alloy billets , 2011 .

[32]  D. StJohn,et al.  An analytical model for constitutional supercooling-driven grain formation and grain size prediction , 2010 .

[33]  D. StJohn,et al.  A model of grain refinement incorporating alloy constitution and potency of heterogeneous nucleant particles , 2001 .