Effects of vehicle driveline parameters and clutch judder on gearbox vibrations

Clutch judder causes discomfort in a car. This undesirable event not only creates noise and vibrations, it also disturbs the normal functionality of other components in the driveline, especially the gearbox, which is prone to oscillating inputs. Although there are numerous separate studies on clutch judder and gearbox vibrations, a combined study is necessary in order to investigate the coupled dynamics, especially the effect of vibrations in a clutch on gearbox vibrations. In this paper, a dynamic model is presented for the driveline, including the details of a gearbox and a dry clutch. It allows us to investigate the effect of clutch parameters and to simulate conditions with and without judder. The obtained dynamical equations are then solved numerically. The influence of judder on gear dynamics and passenger comfort is investigated. The results show that judder causes loss of contact in the gearbox in most cases. In more severe cases of judder, it can cause rattle not only in the unloaded gear, but also in the loaded gears. A modal analysis and a frequency spectrum analysis are conducted as well in order to identify the frequency components of the system vibrations and to verify the obtained results. Parts of the results are compared with the theoretical and experimental data from other research studies, which show agreement and serve to validate the model in this work.

[1]  Semih Sezer,et al.  Vibration isolation with clutch disk pre-damper mechanism for the idle rattle phenomenon , 2018 .

[2]  Rajendra Singh,et al.  Analysis of start-up transient for a powertrain system with a nonlinear clutch damper , 2015 .

[3]  Alok Sinha,et al.  Vibration of Mechanical Systems , 2010 .

[4]  Ahmad Ghasemloonia,et al.  Single and Multiple Misfire Detection in Internal Combustion Engines Using Vold-Kalman Filter Order-Tracking , 2011 .

[5]  Ali Hajnayeb,et al.  An Experimental and Theoretical Study on the Vehicle Brake Judder , 2012 .

[6]  James R. Ottewill,et al.  Intermittent gear rattle due to interactions between forcing and manufacturing errors , 2009 .

[7]  Mehdi Ahmadian,et al.  Analysis of the influence of engine torque excitation on clutch judder , 2017 .

[8]  Riccardo Russo,et al.  Theoretical and experimental investigation into the influence of the periodic backlash fluctuations on the gear rattle , 2011 .

[9]  K. H. Shirazi,et al.  Vibration measurement for crack and rub detection in rotors , 2023, Metrology and Measurement Systems.

[10]  I. Kim,et al.  Influences of the uneven contact pressure and the initial temperature on the hot judder behavior in a multi-disc clutch , 2020, Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology.

[11]  Riccardo Russo,et al.  Gear rattle reduction in an automotive driveline by the adoption of a flywheel with an innovative torsional vibration damper , 2019 .

[12]  Guangqiang Wu,et al.  Driveline Torsional Analysis and Clutch Damper Optimization for Reducing Gear Rattle , 2016 .

[13]  H Jacobsson Disc brake judder considering instantaneous disc thickness and spatial friction variation , 2003 .

[14]  Renfei Yuan,et al.  Dynamic analysis of vehicle start-up judder based on elasto-plastic friction model and dry clutch maneuvering characteristic , 2019 .

[15]  Biao Ma,et al.  Hot judder behavior in multidisc clutches , 2017 .

[16]  Homer Rahnejat,et al.  Effect of clutch lining frictional characteristics on take-up judder , 2017 .

[17]  El-Adl Mohammed Aly Rabeih Torsional vibration analysis of automotive drivelines , 1997 .

[18]  Ashley R. Crowther,et al.  Analysis and simulation of clutch engagement judder and stick-slip in automotive powertrain systems , 2004 .

[19]  Guangqiang Wu,et al.  Mechanism analysis of vehicle start-up judder based on gradient characteristic of Stribeck effect , 2020 .

[20]  Ernesto Rocca,et al.  An analysis of the automotive driveline dynamic behaviour focusing on the influence of the oil squeeze effect on the idle rattle phenomenon , 2007 .

[21]  Homer Rahnejat,et al.  Non-linear multi-body dynamic analysis for the study of clutch torsional vibrations (judder) , 2001 .

[22]  Xingjian Jing,et al.  Modeling and analysis of friction clutch at a driveline for suppressing car starting judder , 2018, Journal of Sound and Vibration.

[23]  Riccardo Russo,et al.  Experimental investigations about the influence of oil lubricant between teeth on the gear rattle phenomenon , 2009 .

[24]  Wentao Sui,et al.  A Simplified Formulation to Estimate Influence of Gearbox Parameters on the Rattle Noise , 2019, Sound&Vibration.

[25]  Subhash Rakheja,et al.  Modeling of automotive driveline system for reducing gear rattles , 2018 .

[26]  Paul D. Walker,et al.  Modeling and simulation of longitudinal dynamics coupled with clutch engagement dynamics for ground vehicles , 2018 .

[27]  Riccardo Russo,et al.  A gear rattle model accounting for oil squeeze between the meshing gear teeth , 2005 .

[28]  Stephen Butt,et al.  Elastodynamic and finite element vibration analysis of a drillstring with a downhole vibration generator tool and a shock sub , 2015 .

[29]  Datong Qin,et al.  Study on the Influence Factors Upon the Propensity to Stick-Slip Phenomenon During Vehicle Start-Up Process , 2020, IEEE Access.