Correlation of wear behavior and indentation fracture resistance in silicon nitride ceramics hot-pressed with alumina and yttria

[1]  S. Sakaguchi,et al.  Influence of Microstructure and Grain Boundary Phase on Tribological Properties of Si3N4 Ceramics , 2008 .

[2]  G. Quinn.  Fracture Toughness of Ceramics by the Vickers Indentation Crack Length Method: A Critical Review , 2007 .

[3]  R. Bradt,et al.  On the Vickers Indentation Fracture Toughness Test , 2007 .

[4]  M. Staia,et al.  Characterization and wear behavior of modified silicon nitride , 2005 .

[5]  P. Blau,et al.  Effect of Incidence Angle on the Impact‐Wear Behavior of Silicon Nitride , 2005 .

[6]  J. Hawk,et al.  Microstructure and abrasive wear in silicon nitride ceramics , 2001 .

[7]  Rui F. Silva,et al.  Effect of α-/β Si3N4-phase ratio and microstructure on the tribological behaviour up to 700°C , 2000 .

[8]  Rui F. Silva,et al.  Tribological characteristics of self-mated couples of Si3N4–SiC composites in the range 22–700°C , 1999 .

[9]  J. Hawk,et al.  Influence of whisker reinforcement on the abrasive wear behavior of silicon nitride- and alumina-based composites , 1997 .

[10]  K. T. Ritchie,et al.  Short‐Crack Toughness and Abrasive Machining of Silicon Nitride , 1996 .

[11]  S. M. Hsu,et al.  Wear and wear transition mechanisms of ceramics , 1996 .

[12]  B. Bai,et al.  Influence of Speed on the Tribochemical Reaction Products and the Associated Transitions for the Dry Sliding of Silicon Nitride against Steel , 1995 .

[13]  Dong F. Wang,et al.  Studies on abrasive wear of monolithic silicon nitride and a silicon carbide whisker-reinforced silicon nitride composite , 1995 .

[14]  Mathias Woydt,et al.  Tribological behavior of silicon nitride materials under unlubricated sliding between 22°C and 1000°C , 1995 .

[15]  S. Kitaoka,et al.  Effect of sintering aids on tribological characteristics of Si3N4 ceramics at 120 °C in water , 1994 .

[16]  S. M. Hsu,et al.  A new parameter for assessment of ceramic wear , 1994 .

[17]  S. M. Hsu,et al.  Processing, Microstructure, and Wear Behavior of Silicon Nitride Hot‐Pressed with Alumina and Yttria , 1994 .

[18]  S. Jahanmir,et al.  Wear transition diagram for silicon nitride , 1993 .

[19]  Mark Gee,et al.  The combined effect of speed and humidity on the wear and friction of silicon nitride , 1993 .

[20]  P. Blau.  Effects of surface preparation on the friction and wear behaviour of silicon nitride/silicon carbide sliding pairs , 1992 .

[21]  P. Becher.  Microstructural design of toughened ceramics , 1991 .

[22]  F. Saito,et al.  Grain Growth During Gas‐Pressure Sintering of β‐Silicon Nitride , 1990 .

[23]  C. Galassi,et al.  Characterization of hot-pressed silicon nitride-based materials by microhardness measurements , 1987 .

[24]  T. Childs,et al.  Fundamentals of friction and wear of materials , 1983 .

[25]  Y. Yoshizawa,et al.  Relationship between fracture toughness determined by surface crack in flexure and fracture resistance measured by indentation fracture for silicon nitride ceramics with various microstructures , 2009 .

[26]  K. Hirao,et al.  Comparison of fracture resistance as measured by the indentation fracture method and fracture toughness determined by the single-edge-precracked beam technique using silicon nitrides with different microstructures , 2007 .

[27]  R. Steinbrech.  Toughening mechanisms for ceramic materials , 1992 .

[28]  A. Mukhopadhyay,et al.  Hardness of silicon nitride and sialon , 1991 .

[29]  T. Miyoshi,et al.  Study on fracture toughness evaluation for structural ceramics. , 1985 .