Finding efficient frontier of process parameters for plastic injection molding

Product quality for plastic injection molding process is highly related with the settings for its process parameters. Additionally, the product quality is not simply based on a single quality index, but multiple interrelated quality indices. To find the settings for the process parameters such that the multiple quality indices can be simultaneously optimized is becoming a research issue and is now known as finding the efficient frontier of the process parameters. This study considers three quality indices in the plastic injection molding: war page, shrinkage, and volumetric shrinkage at ejection. A digital camera thin cover is taken as an investigation example to show the method of finding the efficient frontier. Solidworks and Moldflow are utilized to create the part’s geometry and to simulate the injection molding process, respectively. Nine process parameters are considered in this research: injection time, injection pressure, packing time, packing pressure, cooling time, cooling temperature, mold open time, melt temperature, and mold temperature. Taguchi’s orthogonal array L27 is applied to run the experiments, and analysis of variance is then used to find the significant process factors with the significant level 0.05. In the example case, four process factors are found significant. The four significant factors are further used to generate 34 experiments by complete experimental design. Each of the experiments is run in Moldflow. The collected experimental data with three quality indices and four process factors are further used to generate three multiple regression equations for the three quality indices, respectively. Then, the three multiple regression equations are applied to generate 1,225 theoretical datasets. Finally, data envelopment analysis is adopted to find the efficient frontier of the 1,225 theoretical datasets. The found datasets on the efficient frontier are with the optimal quality. The process parameters of the efficient frontier are further validated by Moldflow. This study demonstrates that the developed procedure has proved a useful optimization procedure that can be applied in practice to the injection molding process.

[1]  H. Öktem,et al.  Application of Taguchi optimization technique in determining plastic injection molding process parameters for a thin-shell part , 2007 .

[2]  Jay Shoemaker,et al.  Moldflow Design Guide: A Resource for Plastics Engineers , 2006 .

[3]  Shu-Kai S. Fan.  Quality improvement of chemical-mechanical wafer planarization process in semiconductor manufacturing using a combined generalized linear modelling - non-linear programming approach , 2000 .

[4]  Sean Walsh.  Shrinkage and Warpage Prediction for Injection Molded Components , 1993 .

[5]  Hasan Kurtaran,et al.  Efficient warpage optimization of thin shell plastic parts using response surface methodology and genetic algorithm , 2006 .

[6]  L. S. Tsou,et al.  Optimal process conditions of shrinkage and warpage of thin‐wall parts , 2004 .

[7]  L. Turng,et al.  A review of current developments in process and quality control for injection molding , 2005 .

[8]  Shih-Jung Liu,et al.  Significance of Processing Parameters on the Warpage of Rotationally Molded Parts , 2002 .

[9]  Babur Ozcelik,et al.  Minimization of warpage and sink index in injection-molded thermoplastic parts using Taguchi optimization method , 2006 .

[10]  G. Box,et al.  On the Experimental Attainment of Optimum Conditions , 1951 .

[11]  Carlos E. Castro,et al.  Multiple criteria optimization with variability considerations in injection molding , 2007 .

[12]  Fred Spiring,et al.  Introduction to Statistical Quality Control , 2007, Technometrics.

[13]  Babur Ozcelik,et al.  Comparison of the warpage optimization in the plastic injection molding using ANOVA, neural network model and genetic algorithm , 2006 .

[14]  T. R. Bement,et al.  Taguchi techniques for quality engineering , 1995 .

[15]  Hasan Kurtaran,et al.  Warpage optimization of a bus ceiling lamp base using neural network model and genetic algorithm , 2005 .

[16]  Huei-Huang Lee,et al.  Application of Taguchi's method on the optimal process design of an injection molded PC/PBT automobile bumper , 1997 .

[17]  B. Ozcelik,et al.  Determination of effecting dimensional parameters on warpage of thin shell plastic parts using integrated response surface method and genetic algorithm , 2005 .

[18]  Ming-Chih Huang,et al.  The effective factors in the warpage problem of an injection-molded part with a thin shell feature , 2001 .

[19]  A. U.S.,et al.  Measuring the efficiency of decision making units , 2003 .

[20]  Ko-Ta Chiang,et al.  Analysis of shrinkage and warpage in an injection-molded part with a thin shell feature using the response surface methodology , 2007 .

[21]  Jaroslav Mackerle.  Finite element modelling of ceramics and glass, an addendum - A bibliography (1998-2004) , 2005 .

[22]  Byung Kim,et al.  Variation of part wall thicknesses to reduce warpage of injection-molded part: Robust design against process variability , 1997 .

[23]  Y. C. Su,et al.  Shrinkage and warpage prediction of injection-molded thin-wall parts using artificial neural networks , 2004 .

[24]  Wu-Lin Chen,et al.  Optimization of plastic injection molding process by dual response surface method with non‐linear programming , 2010 .