Control of interfacial intermetallic compounds in Fe–Al joining by Zn addition

Abstract By Zn addition to the fusion zone, the interfacial intermetallic compounds (IMCs) of laser Al/steel joint changed from layered Fe2Al5 and needle-like FeAl3 to layered Fe2Al5−xZnx and dispersed FeZn10 with minor Al-rich amorphous phase. This resulted in an improvement in the joint strength and the change of failure mode.

[1]  L. M. Zhao,et al.  Effect of interlayer composition on the microstructure and strength of diffusion bonded Mg/Al joint , 2009 .

[2]  J. Park,et al.  Metastable Phases of Dross Particles Formed in a Molten Zinc Bath and Prediction of Soluble Aluminum During Galvannealing Processes , 2012, Metallurgical and Materials Transactions. A.

[3]  S. Katayama,et al.  Mechanical properties of laser-pressure-welded joint between dissimilar galvannealed steel and pure aluminium , 2009 .

[4]  Patrice Peyre,et al.  Generation of aluminium–steel joints with laser-induced reactive wetting , 2007 .

[5]  A. Marder,et al.  The metallurgy of zinc-coated steel , 2000 .

[6]  Z. Jagličić,et al.  Electrical, magnetic and thermal properties of the d-FeZn 10 complex intermetallic phase , 2012 .

[7]  Y. Zhou,et al.  Microstructure Refinement After the Addition of Titanium Particles in AZ31 Magnesium Alloy Resistance Spot Welds , 2012, Metallurgical and Materials Transactions A.

[8]  P. Jacques,et al.  On the joining of steel and aluminium by means of a new friction melt bonding process , 2014 .

[9]  W. Cheng,et al.  Effect of silicon on the formation of intermetallic phases in aluminide coating on mild steel , 2011 .

[10]  Clemens Wallmann,et al.  Fluxless laser beam joining of aluminium with zinc coated steel , 2005 .

[11]  Fei Liu,et al.  Study on Mg/Al Weld Seam Based on Zn–Mg–Al Ternary Alloy , 2014, Materials.

[12]  C. Dong,et al.  Dissimilar metal joining of aluminum alloy to galvanized steel with Al–Si, Al–Cu, Al–Si–Cu and Zn–Al filler wires , 2012 .

[13]  V. Firouzdor,et al.  Al-to-Mg Friction Stir Welding: Effect of Material Position, Travel Speed, and Rotation Speed , 2010 .

[14]  F. Foadian,et al.  A Study on the Formation of Intermetallics During the Heat Treatment of Explosively Welded Al-Ti Multilayers , 2014, Metallurgical and Materials Transactions. A.

[15]  Chunli Yang,et al.  Effects of Si additions on intermetallic compound layer of aluminum–steel TIG welding–brazing joint , 2009 .

[16]  Jürgen Bruckner,et al.  Intermetallic FexAly-phases in a steel/Al-alloy fusion weld , 2007 .

[17]  Sangho Kim,et al.  Brittle intermetallic compound makes ultrastrong low-density steel with large ductility , 2015, Nature.

[18]  Y. Zhou,et al.  Bonding of immiscible Mg and Fe via a nanoscale Fe2Al5 transition layer , 2011 .

[19]  P. Peyre,et al.  Steel to aluminium braze welding by laser process with Al–12Si filler wire , 2008 .

[20]  K. P. Rao,et al.  Study on laser welding-brazing of zinc coated steel to aluminum alloy with a zinc based filler , 2011 .

[21]  Eugen Cicala,et al.  Dissimilar material joining using laser (aluminum to steel using zinc-based filler wire) , 2007 .

[22]  T. Durejko,et al.  Porous graded FeAl intermetallic foams fabricated by sintering process using NaCl space holders , 2015 .

[23]  Yutaka S. Sato,et al.  Constitutional liquation during dissimilar friction stir welding of Al and Mg alloys , 2004 .

[24]  D. García,et al.  Microstructure and mechanical properties of Al-assisted Sintered Fe/Al2O3 Cermets , 1999 .

[25]  A. Röttger,et al.  Phase formation at the interface between a boron alloyed steel substrate and an Al-rich coating , 2013 .

[26]  Sung-Hwan Lim,et al.  Microstructural evaluation of interfacial intermetallic compounds in Cu wire bonding with Al and Au pads , 2014 .

[27]  M. Arai,et al.  Transformation of Fe–Al phase to Fe–Zn phase on pure iron during galvanizing , 1998 .

[28]  J. Hosson,et al.  Relation between microstructure and adhesion of hot dip galvanized zinc coatings on dual phase steel , 2012 .