Metal-embedded SU-8 Slab Techniques for Low-resistance Micromachined Inductors

This work presents a new fabrication technique for micro power inductors by using metal-embedded SU-8 slab molding techniques. The proposed technique uses X-ray lithography to fabricate high-aspect-ratio LIGA-like microstructures in form of embedded structures in the SU-8 slab. This process was applied to fabricate an inductor’s windings with an aspect ratio of 10, which can provide very low resistance but still preserve a small form factor and low profile. Inductors were designed as pot-core structures with overall heights of 370 μm and embedded with 250-μm-thick windings. From the advantage of metal embedded SU-8 slab techniques, 8 μm-thick permalloy core could be fabricated by electroplating around the winding in a single step that could help simplify the process. Four types of inductors were fabricated with 3, 5, 10, and 16 turns in the area of 1.8 to 9.5 mm2. The measured inductance was in the range of 70 nH to 1.3 μH at 1 MHz and DC resistance of 30–336 mΩ for 3–16 turns, respectively. The DC resistance of fabricated inductor was low, as expected, and showed good result compared with the results in literature.

[1]  Mark G. Allen,et al.  Micromachined planar inductors on silicon wafers for MEMS applications , 1998, IEEE Trans. Ind. Electron..

[2]  S. Sugahara,et al.  Micro DC/DC converter that integrates planar inductor on power IC , 2000 .

[3]  Petru Andrei,et al.  INITIAL PERMEABILITY, HYSTERESIS AND TOTAL LOSSES MEASUREMENTS , 2000 .

[4]  C. Ahn,et al.  Micromachined spiral inductors using UV-LIGA techniques , 2001 .

[5]  S. Han,et al.  A megahertz switching DC/DC converter using FeBN thin film inductor , 2002 .

[6]  M. Saidani,et al.  Cubic millimeter power inductor fabricated in batch-type wafer technology , 2003 .

[7]  E. Brandon,et al.  Fabrication and characterization of microinductors for distributed power converters , 2003 .

[8]  M. Allen,et al.  Ultralow-profile micromachined power inductors with highly laminated Ni/Fe cores: application to low-megahertz DC-DC converters , 2003 .

[9]  M. Yamaguchi,et al.  All-in-one package ultracompact micropower module using thin-film inductor , 2004, IEEE transactions on magnetics.

[10]  M. Brunet,et al.  High-frequency micro-machined power inductors , 2005 .

[11]  Yongsoo Oh,et al.  Planar inductor with ferrite layers for DC-DC converter , 2005, The 13th International Conference on Solid-State Sensors, Actuators and Microsystems, 2005. Digest of Technical Papers. TRANSDUCERS '05..

[12]  R. Hida,et al.  Low-Resistance Integrated Toroidal Inductor for Power Management , 2006, IEEE transactions on magnetics.

[13]  P. Hazucha,et al.  A 100MHz Eight-Phase Buck Converter Delivering 12A in 25mm2 Using Air-Core Inductors , 2007, APEC 07 - Twenty-Second Annual IEEE Applied Power Electronics Conference and Exposition.

[14]  T. O'Donnell,et al.  Micro-inductors integrated on silicon for power supply on chip , 2007 .

[15]  D. O'Sullivan,et al.  Microfabricated inductors for 20 MHz Dc-Dc converters , 2008, 2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition.

[16]  K. Ngo,et al.  SU-8 enhanced high power density MEMS inductors , 2008, 2008 34th Annual Conference of IEEE Industrial Electronics.

[17]  K. Ngo,et al.  Silicon molding techniques for integrated power MEMS inductors , 2011 .

[18]  Saibal Roy,et al.  High frequency DC-DC converter with co-packaged planar inductor and power IC , 2013, 2013 IEEE 63rd Electronic Components and Technology Conference.

[19]  S. Sujitjorn,et al.  Al Microheater and Ni Temperature Sensor Set based-on Photolithography with Closed-Loop Control , 2015 .

[20]  Thierry Lebey,et al.  Thermal Behavior of an Integrated Square Spiral Micro Coil , 2015 .

[21]  Richard E. Anderson,et al.  S-Parameter Techniques for Faster , More Accurate Network Design , 2022 .