Performance optimization of thermoelectric generators designed by multi-objective genetic algorithm

Abstract The purpose of this study is to investigate the output power and efficiency of a TEG system using waste heat from heat pipes, and then optimize its performance. The TEG material is Bi0.4Sb1.6Te3 and its figure-of-merit (ZT) is 1.18 at room temperature. The predictions indicate that a longer length of the elements has greater power output and efficiency based on a fixed heat flux on the hot side surface, whereas a shorter length has greater output power based on a fixed temperature difference. The geometry of the TEG is designed through a multi-objective genetic algorithm (MOGA) to maximize its efficiency. When the temperature difference is fixed at 40 °C, the output power and efficiency of the TEG with optimization is increased by about 51.9% and 5.4%, compared to the TEG without optimization. Once the impedance matching, namely, the internal resistance is equal to the external load resistance, is used, the output power can be further enhanced by about 3.85–4.40%. When the heat flux is fixed at 20,000 Wm−2 along with the temperature difference of 40 °C, the output power and efficiency of a pair of elements can be increased to 7.99 mW and 9.52%, respectively. These results are much higher than those reported in other studies. Accordingly, it is concluded that the MOGA is a powerful tool to design the geometry of a TEG for maximizing its performance and real applications in industry.

[1]  Chul-Hee Lee,et al.  Influence of powder size on thermoelectric properties of p-type 25%Bi2Te375%Sb2Te3 alloys fabricated using gas-atomization and spark-plasma sintering , 2016 .

[2]  Yu Li Lin,et al.  Power output and efficiency of a thermoelectric generator under temperature control , 2016 .

[3]  Robin Smith,et al.  Modelling and screening heat pump options for the exploitation of low grade waste heat in process sites , 2016 .

[4]  Joseph Richardson,et al.  High-Performance Nanostructured Thermoelectric Generators for Micro Combined Heat and Power Systems , 2016 .

[5]  Peter M. Attia,et al.  Modeling passive power generation in a temporally-varying temperature environment via thermoelectrics , 2013 .

[6]  Qi Wang,et al.  A review of thermoelectrics research – Recent developments and potentials for sustainable and renewable energy applications , 2014 .

[7]  Luca Podofillini,et al.  Optimal reliability/availability of uncertain systems via multi-objective genetic algorithms , 2004, IEEE Transactions on Reliability.

[8]  Ana Sánchez,et al.  RAMS+C informed decision-making with application to multi-objective optimization of technical specifications and maintenance using genetic algorithms , 2005, Reliab. Eng. Syst. Saf..

[9]  Gequn Shu,et al.  A review of waste heat recovery on two-stroke IC engine aboard ships , 2013 .

[10]  Gao Min,et al.  Model for geometry optimisation of thermoelectric devices in a hybrid PV/TE system , 2016 .

[11]  Wei Zhu,et al.  Thin-film solar thermoelectric generator with enhanced power output: Integrated optimization design to obtain directional heat flow , 2015 .

[12]  Yu Li Lin,et al.  Performance of a thermoelectric generator intensified by temperature oscillation , 2017 .

[13]  Jiangming Kan,et al.  Theoretical and experimental analysis of a solar thermoelectric power generation device based on gravity-assisted heat pipes and solar irradiation , 2016 .

[14]  I. V. Bezsudnov,et al.  Rotating thermoelectric device in periodic steady state , 2014 .

[15]  Xiaolong Gou,et al.  Modeling, experimental study and optimization on low-temperature waste heat thermoelectric generator system , 2010 .

[16]  Wei-Keng Lin,et al.  Geometric optimization of thermoelectric coolers in a confined volume using genetic algorithms , 2005 .

[17]  J. Ji,et al.  Recent development and application of thermoelectric generator and cooler , 2015 .

[18]  L. Rosendahl,et al.  A three-dimensional numerical model of thermoelectric generators in fluid power systems , 2011 .

[19]  Bongkyun Jang,et al.  Optimal design for micro-thermoelectric generators using finite element analysis , 2011 .

[20]  Aliakbar Akbarzadeh,et al.  Theoretical and experimental study on heat pipe cooled thermoelectric generators with water heating using concentrated solar thermal energy , 2014 .

[21]  Gequn Shu,et al.  A comprehensive design method for segmented thermoelectric generator , 2015 .

[22]  Z. Chen,et al.  Hydrothermal synthesized nanostructure Bi–Sb–Te thermoelectric materials , 2014 .

[23]  Gequn Shu,et al.  Elucidating modeling aspects of thermoelectric generator , 2015 .

[24]  A. Akbarzadeh,et al.  Simultaneous power generation and heat recovery using a heat pipe assisted thermoelectric generator system , 2015 .

[25]  James W. Evans,et al.  Printed flexible thermoelectric generators for use on low levels of waste heat , 2015 .

[26]  Yan Yan,et al.  Periodic heating amplifies the efficiency of thermoelectric energy conversion , 2013 .

[27]  Xiao-dong Wang,et al.  Dynamic response characteristics of thermoelectric generator predicted by a three-dimensional heat-electricity coupled model , 2014 .

[28]  Ke Li,et al.  Configuration parameters design and optimization for plate-fin heat exchangers with serrated fin by multi-objective genetic algorithm , 2016 .

[29]  Guobin Zhang,et al.  A comprehensive and time-efficient model for determination of thermoelectric generator length and cross-section area , 2016 .

[30]  Yuehong Su,et al.  A study on incorporation of thermoelectric modules with evacuated-tube heat-pipe solar collectors , 2012 .

[31]  Clemens Forman,et al.  Estimating the global waste heat potential , 2016 .

[32]  Marcello Chiaberge,et al.  Design and characterization of small thermoelectric generators for environmental monitoring devices , 2013 .

[33]  Wei-Hsin Chen,et al.  Performance analysis and optimum operation of a thermoelectric generator by Taguchi method , 2015 .

[34]  Lin Wang,et al.  Structural optimisation of vertical-axis wind turbine composite blades based on finite element analysis and genetic algorithm , 2016 .

[35]  Yuying Yan,et al.  A potential candidate for the sustainable and reliable domestic energy generation–Thermoelectric cogeneration system , 2013 .

[36]  Chang Chung Yang,et al.  Modeling and simulation for the design of thermal-concentrated solar thermoelectric generator , 2014 .

[37]  Gequn Shu,et al.  Start-up modes of thermoelectric generator based on vehicle exhaust waste heat recovery , 2015 .

[38]  William T. Choate,et al.  Waste Heat Recovery. Technology and Opportunities in U.S. Industry , 2008 .

[39]  Aliakbar Akbarzadeh,et al.  Experimental investigation of combined heat recovery and power generation using a heat pipe assisted thermoelectric generator system , 2016 .

[40]  Jeff Sharp,et al.  Overview of Solid-State Thermoelectric Refrigerators and Possible Applications to On-Chip Thermal Management , 2006, Proceedings of the IEEE.

[41]  Frédéric Lesage,et al.  Experimental analysis of peak power output of a thermoelectric liquid-to-liquid generator under an increasing electrical load resistance , 2013 .

[42]  Yi-Hsiang Cheng,et al.  Maximizing the cooling capacity and COP of two-stage thermoelectric coolers through genetic algorithm , 2006 .

[43]  Cheng-Ting Hsu,et al.  Experiments and simulations on low-temperature waste heat harvesting system by thermoelectric power generators , 2011 .