Highly accurate online characterisation of cracks in plate-like structures

Abstract In this paper, an in situ technique for the localisation and the sizing of cracks in plate-like structures is presented. The excitation and the reception of the ultrasonic diagnostic signal – Lamb waves – are achieved by permanently installed piezoelectric ceramic disks. The technique simplifies the underdetermined problem of the full characterisation of cracks to an over-determined problem of the localisation of crack tips. Also, it overcomes the difficulties associated with using the pitch-catch excitation scheme for crack characterisation. The development of the technique was done systematically using analytic models and the finite element method. The technique has been validated by an experiment and assessed by extensive parametric studies. While it was designed to be a convenient approach, highly accurate crack characterisation has been attained as evident through the results of both numerical studies and physical experiments.

[1]  F. Chang,et al.  Detection and monitoring of hidden fatigue crack growth using a built-in piezoelectric sensor/actuator network: I. Diagnostics , 2004 .

[2]  Carlos E. S. Cesnik,et al.  Finite-dimensional piezoelectric transducer modeling for guided wave based structural health monitoring , 2005 .

[3]  Lin Ye,et al.  Some aspects of numerical simulation for Lamb wave propagation in composite laminates , 2006 .

[4]  J. Rose.  Ultrasonic Waves in Solid Media , 1999 .

[5]  P. Cawley,et al.  Amplitude spectrum method for the measurement of phase velocity , 1989 .

[6]  Victor Giurgiutiu,et al.  Interaction of Lamb waves with rivet hole cracks from multiple directions , 2017 .

[7]  E. Crawley,et al.  Use of piezoelectric actuators as elements of intelligent structures , 1987 .

[8]  M. Aliabadi,et al.  Assessment of delay-and-sum algorithms for damage detection in aluminium and composite plates , 2014 .

[9]  L. Ye,et al.  Quantitative assessment of through-thickness crack size based on Lamb wave scattering in aluminium plates , 2008 .

[10]  Z. Chang,et al.  Scattering of Lamb waves from a rivet hole with edge cracks , 1999 .

[11]  F. Yuan,et al.  Diagnostic Lamb waves in an integrated piezoelectric sensor/actuator plate: analytical and experimental studies , 2001 .

[12]  J. Michaels.  Detection, localization and characterization of damage in plates with an in situ array of spatially distributed ultrasonic sensors , 2008 .

[13]  Wei Zhao,et al.  Piezoelectric wafer active sensor embedded ultrasonics in beams and plates , 2003 .

[14]  Bradford W. Parkinson,et al.  Global positioning system : theory and applications , 1996 .

[15]  Zhongqing Su,et al.  Fundamental Lamb Mode-based Delamination Detection for CF/EP Composite Laminates Using Distributed Piezoelectrics , 2004 .

[16]  Victor Giurgiutiu,et al.  Guided Wave Based Crack Detection in the Rivet Hole Using Global Analytical with Local FEM Approach , 2016, Materials.

[17]  V. Giurgiutiu.  Tuned Lamb Wave Excitation and Detection with Piezoelectric Wafer Active Sensors for Structural Health Monitoring , 2005 .

[18]  V. Giurgiutiu,et al.  In situ 2-D piezoelectric wafer active sensors arrays for guided wave damage detection. , 2008, Ultrasonics.

[19]  Joseph L. Rose,et al.  Active health monitoring of an aircraft wing with embedded piezoelectric sensor/actuator network: I. Defect detection, localization and growth monitoring , 2007 .

[20]  Carlos E. S. Cesnik,et al.  Review of guided-wave structural health monitoring , 2007 .

[21]  B. Masserey,et al.  In-situ monitoring of fatigue crack growth using high frequency guided waves , 2015 .

[22]  Li Cheng,et al.  Artificial Neural Network (ANN)-based Crack Identification in Aluminum Plates with Lamb Wave Signals: , 2009 .

[23]  E. Manoach,et al.  An Investigation on Vibration-based Damage Detection in Circular Plates , 2009 .