Deep etching of silicon with smooth sidewalls by an improved gas-chopping process using a Faraday cage and a high bias voltage

A silicon substrate, masked with oxide lines with a spacing of 1μm, was etched using a gas-chopping process designed to enhance mask selectivity and produce a highly anisotropic etch profile with ripple-free sidewalls. The gas-chopping process employed a high bias voltage of −200V and a Faraday cage in the etching step. The use of a high bias voltage relieved the curvature of sidewall ripples that are generated during etch cycles due to the bombardment of energetic ions on the convex portions of the ripples, thus flattening the sidewall surface. The use of a Faraday cage served to suppress the erosion of the mask, thus leading to a high mask selectivity. This can be attributed to an increase in the intrinsic etch selectivity of the Si substrate to the mask due to an increase in the ratio of neutral to ion fluxes on the substrate, and by the suppression of mask faceting due to a reduction in the etch yields of the oxide mask and a CFx film formed on the surface of the mask.

[1]  Kazunori Tsujimoto,et al.  Low‐temperature reactive ion etching and microwave plasma etching of silicon , 1988 .

[2]  S. Moon,et al.  Sidewall-angle effect on the bottom etch profile in SiO2 etching using a CF4 plasma , 2001 .

[3]  G. D. Boyd,et al.  Directional reactive ion etching at oblique angles , 1980 .

[4]  S. Moon,et al.  Angular dependence of the redeposition rates during SiO2 etching in a CF4 plasma , 2001 .

[5]  Patrick J. French,et al.  Advanced time-multiplexed plasma etching of high aspect ratio silicon structures , 2002 .

[6]  S. Aachboun,et al.  Deep anisotropic etching of silicon , 1999 .

[7]  W. Yoo,et al.  Investigation of in situ trench etching process and Bosch process for fabricating high-aspect-ratio beams for microelectromechanical systems , 2002 .

[8]  Simulation of plasma molding over a ring on a flat surface , 2003 .

[9]  S. Moon,et al.  Trajectories of ions inside a Faraday cage located in a high density plasma etcher , 2003 .

[10]  E. V. D. Drift,et al.  Balancing the etching and passivation in time-multiplexed deep dry etching of silicon , 2001 .

[11]  S. Moon,et al.  Improvement of SiO2 pattern profiles etched in CF4 and SF6 plasmas by using a Faraday cage and neutral beams , 2005 .

[12]  S. Moon,et al.  More vertical etch profile using a Faraday cage in plasma etching , 1999 .

[13]  M. Boufnichel,et al.  Cryogenic etching of deep narrow trenches in silicon , 2000 .

[14]  S. Moon,et al.  Redeposition of etch products on sidewalls during SiO2 etching in a fluorocarbon plasma. I. Effect of particle emission from the bottom surface in a CF4 plasma , 2002 .

[15]  S. Moon,et al.  Angular dependence of SiO2 etch rate at various bias voltages in a high density CHF3 plasma , 2002 .

[16]  Plasma molding over deep trenches and the resulting ion and energetic neutral distributions , 2003 .

[17]  R. Boswell,et al.  Etching silicon by SF6 in a continuous and pulsed power helicon reactor , 2003 .

[18]  J. Coburn,et al.  Ion-beam-assisted etching of Si with fluorine at low temperatures , 1994 .

[19]  Ivo W. Rangelow,et al.  Critical tasks in high aspect ratio silicon dry etching for microelectromechanical systems , 2003 .

[20]  Robert E. Lee.  Microfabrication by ion‐beam etching , 1979 .

[21]  S. Moon,et al.  Angular dependence of etch rates in the etching of poly-Si and fluorocarbon polymer using SF6, C4F8, and O2 plasmas , 2004 .

[22]  R. A. Barker,et al.  Investigation of plasma etching mechanisms using beams of reactive gas ions , 1981 .

[23]  Ivo W. Rangelow,et al.  Dry etching with gas chopping without rippled sidewalls , 1999 .

[24]  S. Ingram.  The influence of substrate topography on ion bombardment in plasma etching , 1990 .

[25]  Hans Loschner,et al.  Reactive ion etching for microelectrical mechanical system fabrication , 1995 .