Device-level hermetic packaging of microresonators by RTP aluminum-to-nitride bonding

This paper presents a device-level microelectromechanical systems (MEMS) packaging process with accelerated tests and reliability analysis. Surface-micromachined microresonators are sealed inside microcavities by a rapid thermal processing (RTP) aluminum-to-silicon nitride bonding and packaging technique. Chip-to-chip bonding is used to form packages both under atmospheric pressure and in vacuum. The hermeticity of the package seals are evaluated by IPA (isopropyl alcohol) leak tests. The vacuum seal is evaluated by measuring the Q-factor (quality factor) of the packaged microresonators. The measured Q-factor of a vacuum-packaged comb-resonator is 1800/spl plusmn/200, corresponding to a 200 motor vacuum inside the micro cavity, and has not degraded over 37 weeks of shelf-life. The reliability information is evaluated by combining accelerated testing of the packages in a harsh environment (an autoclave chamber, 130/spl deg/C, 2.7 atm and 100% RH) and statistical analysis. The mean-time-to-failure (MTTF) of the packaged device is estimated as 29.7 weeks in an autoclave chamber, and tests on vacuum-packaged devices have confirmed the estimation.

[1]  William C. Tang,et al.  Electrostatic-comb drive of lateral polysilicon resonators , 1990 .

[2]  Shinji Kobayashi,et al.  Double-frame silicon gyroscope packaged under low pressure by wafer bonding (特集 振動型センサ・アクチュエータ) , 2000 .

[3]  Henry Guckel,et al.  Surface micromachined pressure transducers , 1991 .

[4]  K. Najafi,et al.  A hermetic glass-silicon micropackage with high-density on-chip feedthroughs for sensors and actuators , 1996 .

[5]  R. Howe,et al.  Microelectromechanical filters for signal processing , 1992, [1992] Proceedings IEEE Micro Electro Mechanical Systems.

[6]  C. Harendt,et al.  Silicon fusion bonding and its characterization , 1992 .

[7]  J. Lau,et al.  Solder Joint Reliability of BGA, CSP, Flip Chip, and Fine Pitch SMT Assemblies , 1996 .

[8]  U. Gosele,et al.  Gas tightness of cavities sealed by silicon wafer bonding , 1997, Proceedings IEEE The Tenth Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Robots.

[9]  Elmer E Lewis,et al.  Introduction To Reliability Engineering , 1987 .

[10]  E. Beyne,et al.  The indent reflow sealing (IRS) technique-a method for the fabrication of sealed cavities for MEMS devices , 2000, Journal of Microelectromechanical Systems.

[11]  A. Roth.  Vacuum sealing techniques , 1966 .

[12]  K. Fujiwara,et al.  Diffusion of aluminum into silicon nitride films , 1978 .

[13]  R. Wolffenbuttel,et al.  Vacuum sealing of microcavities using metal evaporation , 1997 .

[14]  K. Najafi,et al.  Localized silicon fusion and eutectic bonding for MEMS fabrication and packaging , 1998, Journal of Microelectromechanical Systems.

[15]  Kensall D. Wise,et al.  Batch-processed vacuum-sealed capacitive pressure sensors , 2001 .

[16]  Kensall D. Wise,et al.  Wafer-Level Packaging Using Localized Mass Deposition , 2001 .

[17]  William C. Tang,et al.  Electrostatic Comb Drive for Resonant Sensor and Actuator Applications , 1990 .

[18]  M. Shimbo,et al.  Silicon‐to‐silicon direct bonding method , 1986 .

[19]  Liwei Lin,et al.  Accelerated hermeticity testing of a glass-silicon package formed by rapid thermal processing aluminum-to-silicon nitride bending , 2002 .

[20]  J. O’Hanlon.  A User's Guide to Vacuum Technology , 1980 .

[21]  Richard Ulrich,et al.  Advanced electronic packaging , 2006 .

[22]  U. Gösele,et al.  SemiConductor Wafer Bonding: Science and Technology , 1998 .

[23]  Liwei Lin,et al.  Hermetic wafer bonding based on rapid thermal processing , 2001 .

[24]  Mu Chiao,et al.  Accelerated Hermeticity Testing of a Glass-Silicon Package Formed by RTP Aluminum-to-Silicon Nitride Bonding , 2001 .

[25]  Andrew D. Oliver,et al.  100% foundry compatible packaging and full wafer release and die separation technique for surface micromachined devices , 2000 .

[26]  K. Najafi,et al.  Vacuum packaging technology using localized aluminum/silicon-to-glass bonding , 2002, Technical Digest. MEMS 2001. 14th IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.01CH37090).

[27]  K. Najafi,et al.  A low-temperature thin-film electroplated metal vacuum package , 2004, Journal of Microelectromechanical Systems.

[28]  Liwei Lin.  MEMS post-packaging by localized heating and bonding , 2000 .

[29]  A. Cohen.  Truncated and Censored Samples: Theory and Applications , 1991 .