Can segmented flow enhance heat transfer in microchannel heat sinks

Abstract Liquid cooling is an efficient way to remove heat fluxes with magnitudes up to 10,000 W/cm2. One limitation of current single-phase microchannel heat sinks is the relatively low Nusselt number, due to laminar flow. In this work, we experimentally investigate how to enhance the Nusselt number with the introduction of segmented flow. The segmented flow pattern was created by the periodic injection of air bubbles through a T-junction into water-filled channels. We designed a polycarbonate heat sink consisting of an array of seven parallel microchannels each with a square cross-section 500 μm wide. We show that segmented flow increases the Nusselt number of laminar flow by more than 100%, provided the mass velocity of the liquid is within the range 330–2000 kg/m2 s.

[1]  Tsung-Hsun Tsai,et al.  Performance analysis of nanofluid-cooled microchannel heat sinks , 2007 .

[2]  Satish G. Kandlikar,et al.  High Flux Heat Removal with Microchannels—A Roadmap of Challenges and Opportunities , 2005 .

[3]  I. Mudawar,et al.  Flow boiling heat transfer in two-phase micro-channel heat sinks––I. Experimental investigation and assessment of correlation methods , 2003 .

[5]  Y. Peles,et al.  Suppression of Boiling Flow Oscillations in Parallel Microchannels by Inlet , 2006 .

[6]  Matthias Heil,et al.  The steady propagation of a semi-infinite bubble into a tube of elliptical or rectangular cross-section , 2002, Journal of Fluid Mechanics.

[7]  K. Jensen,et al.  Multiphase microfluidics: from flow characteristics to chemical and materials synthesis. , 2006, Lab on a chip.

[8]  D. E. Beasley,et al.  Theory and design for mechanical measurements , 1991 .

[9]  Jie Xu,et al.  Use of a porous membrane for gas bubble removal in microfluidic channels: physical mechanisms and design criteria , 2010, 1005.0107.

[10]  S. Garimella,et al.  Thermally Developing Flow and Heat Transfer in Rectangular Microchannels of Different Aspect Ratios , 2006 .

[11]  D. Poulikakos,et al.  On two-phase flow patterns and transition criteria in aqueous methanol and CO2 mixtures in adiabatic, rectangular microchannels , 2009 .

[12]  I. Mudawar,et al.  Measurement and prediction of pressure drop in two-phase micro-channel heat sinks , 2003 .

[13]  David F. Fletcher,et al.  Laminar Flow and Heat Transfer in a Periodic Serpentine Channel , 2005 .

[14]  Issam Mudawar.  Assessment of high-heat-flux thermal management schemes , 2001 .

[15]  R. Pease,et al.  High-performance heat sinking for VLSI , 1981, IEEE Electron Device Letters.

[16]  Chih-Ming Ho,et al.  Transport of bubbles in square microchannels , 2002 .

[17]  Y. Peles,et al.  Bubble Dynamics During Boiling in Enhanced Surface Microchannels , 2006, Journal of Microelectromechanical Systems.

[18]  I. Mudawar,et al.  Ultra-high critical heat flux (CHF) for subcooled water flow boiling—I: CHF data and parametric effects for small diameter tubes , 1999 .

[19]  David F. Fletcher,et al.  Laminar flow and heat transfer in a periodic trapezoidal channel with semi-circular cross-section , 2006 .

[20]  S. Kandlikar,et al.  An Experimental Investigation of Flow Boiling Characteristics of Water in Parallel Microchannels , 2004 .

[21]  I. Mudawar,et al.  Flow boiling heat transfer in two-phase micro-channel heat sinks--II. Annular two-phase flow model , 2003 .

[22]  S. Kandlikar,et al.  Optimization of Microchannel Geometry for Direct Chip Cooling Using Single Phase Heat Transfer , 2004 .

[23]  Y. Katoh,et al.  Free convection heat transfer from vertical and horizontal short plates , 1985 .

[24]  Freek Kapteijn,et al.  Multiphase monolith reactors: Chemical reaction engineering of segmented flow in microchannels , 2005 .

[25]  Dimos Poulikakos,et al.  Efficiency of optimized bifurcating tree-like and parallel microchannel networks in the cooling of electronics , 2009 .

[26]  Djamel Lakehal,et al.  Computational heat transfer and two-phase flow topology in miniature tubes , 2008 .

[27]  S. Quake,et al.  Dynamic pattern formation in a vesicle-generating microfluidic device. , 2001, Physical review letters.

[28]  Yoav Peles,et al.  Pressure effects on flow boiling instabilities in parallel microchannels , 2009 .

[29]  Chris R. Kleijn,et al.  Velocity fluctuations of segmented flow in microchannels , 2008 .

[30]  M. Yovanovich,et al.  Laminar Forced Convection Heat Transfer in the Combined Entry Region of Non-Circular Ducts , 2004 .

[31]  Martin A. Abraham,et al.  Bubble-train flow in capillaries of circular and square cross section , 1995 .

[32]  I. Mudawar,et al.  Assessment of the effectiveness of nanofluids for single-phase and two-phase heat transfer in micro-channels , 2007 .

[33]  Yoav Peles,et al.  Flow boiling of water in a circular staggered micro-pin fin heat sink , 2008 .

[34]  Axel Günther,et al.  Micromixing of miscible liquids in segmented gas-liquid flow. , 2005, Langmuir : the ACS journal of surfaces and colloids.

[35]  George M. Homsy,et al.  MODELING SHAPES AND DYNAMICS OF CONFINED BUBBLES , 2006 .

[36]  H. Stone,et al.  Transition from squeezing to dripping in a microfluidic T-shaped junction , 2008, Journal of Fluid Mechanics.

[37]  Saif A. Khan,et al.  Transport and reaction in microscale segmented gas-liquid flow. , 2004, Lab on a chip.

[38]  Chin Pan,et al.  Gas-liquid two-phase flow in micro-channels , 2002 .

[39]  Albert Mosyak,et al.  Heat transfer of gas–liquid mixture in micro-channel heat sink , 2009 .

[40]  J. Thome,et al.  State of the Art of High Heat Flux Cooling Technologies , 2007 .

[41]  Clayton J. Radke,et al.  The motion of long bubbles in polygonal capillaries. Part 2. Drag, fluid pressure and fluid flow , 1995, Journal of Fluid Mechanics.