Numerical study of an exhaust heat recovery system using corrugated tube heat exchanger with twisted tape inserts

Abstract The purpose of this work is to investigate gas to liquid heat transfer performance of concentric tube heat exchanger with twisted tape inserted corrugated tube and to evaluate its impact on engine performance and economics through heat recovery from the exhaust of a heavy duty diesel generator (120 ekW rated load). This type of heat exchanger is expected to be inexpensive to install and effective in heat transfer and to have minimal effect on exhaust emissions of diesel engines. This type of heat exchanger has been investigated for liquid to liquid heat transfer at low Reynolds number by few investigators, but not for gas to liquid heat transfer. In this paper, a detail of heat transfer performance is investigated through simulations using computer software. The software is first justified by comparing the simulation results with the developed renowned correlations. Simulations are then conducted for concentric tube heat exchanger with different twisted tape configuration for optimal design. The results show that the enhancement in the rate of heat transfer in annularly corrugated tube heat exchanger with twisted tape is about 235.3% and 67.26% when compared with the plain tube and annularly corrugated tube heat exchangers without twisted tapes respectively. Based on optimal results, for a 120 ekW diesel generator, the application of corrugated tube with twisted tape concentric tube heat exchanger can save 2250 gal of fuel, $11,330 of fuel cost annually and expected payback of 1 month. In addition, saving in heating fuel also reduces in CO 2 emission by 23 metric tons a year.

[1]  Masoud Rahimi,et al.  Experimental and CFD studies on heat transfer and friction factor characteristics of a tube equipped with modified twisted tape inserts , 2009 .

[2]  P. Promvonge.  Thermal augmentation in circular tube with twisted tape and wire coil turbulators , 2008 .

[3]  P. Naphon,et al.  Single-phase heat transfer and pressure drop in the micro-fin tubes with coiled wire insert ☆ , 2006 .

[4]  A. Viedma,et al.  Experimental study of heat transfer enhancement with wire coil inserts in laminar-transition-turbulent regimes at different Prandtl numbers , 2005 .

[5]  Pongjet Promvonge,et al.  Experimental investigation of heat transfer and flow friction in a circular tube fitted with regularly spaced twisted tape elements , 2006 .

[6]  Animesh Dutta,et al.  Friction and heat transfer characteristics of laminar swirl flow through a circular tube fitted with regularly spaced twisted-tape elements , 2001 .

[7]  Smith Eiamsa-ard,et al.  3-D Numerical simulation of swirling flow and convective heat transfer in a circular tube induced by means of loose-fit twisted tapes☆ , 2009 .

[8]  Abhijit Date,et al.  Friction and heat transfer characteristics of flow through square duct with twisted tape insert , 2003 .

[9]  Chinaruk Thianpong,et al.  Compound heat transfer enhancement of a dimpled tube with a twisted tape swirl generator , 2009 .

[10]  Pongjet Promvonge,et al.  Heat transfer behaviors in a tube with combined conical-ring and twisted-tape insert ☆ , 2007 .

[11]  S. F. Al-Fahed,et al.  Pressure drop and heat transfer comparison for both microfin tube and twisted-tape inserts in laminar flow , 1998 .

[12]  Pongjet Promvonge,et al.  Thermal performance in circular tube fitted with coiled square wires , 2008 .

[13]  Shyy Woei Chang,et al.  Heat transfer and pressure drop in tube with broken twisted tape insert , 2007 .

[14]  P. Lettieri,et al.  An introduction to heat transfer , 2007 .

[15]  Pongjet Promvonge,et al.  Enhancement of heat transfer in a tube with regularly-spaced helical tape swirl generators , 2005 .

[16]  A. W. Date,et al.  Heat transfer and pressure drop in a spirally grooved tube with twisted tape insert , 2009 .