Electrochemical Activity and Catalyst Utilization of Low Pt and Thickness Controlled Membrane Electrode Assemblies

An improved catalyst deposition methodology based on a piezo-electric printing technique has been developed and used to fabricate catalyst coated membranes (CCM) with thin catalyst layers (1-5 μm) and ultra-low Pt loadings (0.02-0.12 mg Pt /cm 2 ). The performance of these CCMs was examined in proton exchange membrane fuel cells (PEMFCs). The catalyst utilization was observed to increase with decreasing catalyst layer thickness (decreasing Pt loading). The printed CCM with two layers containing an ultra-low Pt loading (0.02 mg Pt /cm 2 ) exhibited Pt utilizations of 100%. Neglecting the anode contributions, the mass activity at 850 mV for the printed CCM is nearly 76.5 mA/mg Pt which is 3.5 times higher than that for the CCM fabricated by conventional spraying method (22.5 mA/mg Pt ).

[1]  Frédéric Maillard,et al.  Impact of ultra-low Pt loadings on the performance of anode/cathode in a proton-exchange membrane fuel cell , 2010 .

[2]  P. Garcia-Ybarra,et al.  Electrospray deposition of catalyst layers with ultra-low Pt loadings for PEM fuel cells cathodes , 2010 .

[3]  E. Müller,et al.  Real surface area measurements of Pt3Co/C catalysts , 2010 .

[4]  S. Liao,et al.  Performance of an ultra-low platinum loading membrane electrode assembly prepared by a novel catalyst-sprayed membrane technique , 2010 .

[5]  G. Lindbergh,et al.  Active Area Determination for Porous Pt-Electrodes used in PEM Fuel Cells - Temperature And Humidity Effects , 2009 .

[6]  L. Zhenxing,et al.  Investigation of a Novel Catalyst Coated Membrane Method to Prepare Low‐Platinum‐Loading Membrane Electrode Assemblies for PEMFCs , 2009 .

[7]  Kaspar Andreas Friedrich,et al.  Investigation of electrode composition of polymer fuel cells by electrochemical impedance spectroscopy , 2008 .

[8]  Michael Rottmayer,et al.  Ink-jet printing of electrolyte and anode functional layer for solid oxide fuel cells , 2008 .

[9]  Peter C. Rieke,et al.  Fabrication of polymer electrolyte membrane fuel cell MEAs utilizing inkjet print technology , 2007 .

[10]  André D. Taylor,et al.  Inkjet printing of carbon supported platinum 3-D catalyst layers for use in fuel cells , 2007 .

[11]  Mahlon Wilson,et al.  Scientific aspects of polymer electrolyte fuel cell durability and degradation. , 2007, Chemical reviews.

[12]  J. Jorné,et al.  Study of the Exchange Current Density for the Hydrogen Oxidation and Evolution Reactions , 2007 .

[13]  Kunal Karan.  Assessment of transport-limited catalyst utilization for engineering of ultra-low Pt loading polymer electrolyte fuel cell anode , 2007 .

[14]  Sanjeev Mukerjee,et al.  High performance polymer electrolyte fuel cells with ultra-low Pt loading electrodes prepared by dual ion-beam assisted deposition , 2006 .

[15]  Cheng-Hsien Tsai,et al.  Effects of sputtering parameters on the performance of electrodes fabricated for proton exchange membrane fuel cells , 2006 .

[16]  M. Arenz,et al.  CO surface electrochemistry on Pt-nanoparticles: A selective review , 2005 .

[17]  Arumugam Manthiram,et al.  High performance membrane-electrode assemblies with ultra-low Pt loading for proton exchange membrane fuel cells , 2005 .

[18]  C. Bock,et al.  Characteristics of adsorbed CO and CH3OH oxidation reactions for complex Pt/Ru catalyst systems , 2005 .

[19]  H. Gasteiger,et al.  Activity benchmarks and requirements for Pt, Pt-alloy, and non-Pt oxygen reduction catalysts for PEMFCs , 2005 .

[20]  H. R. Kunz,et al.  High-Performance PEMFCs at Elevated Temperatures Using Nafion 112 Membranes , 2005 .

[21]  U. Stimming,et al.  Infrared spectroscopic study of CO adsorption and electro-oxidation on carbon-supported Pt nanoparticles: Interparticle versus intraparticle heterogeneity , 2004 .

[22]  Hubert A. Gasteiger,et al.  Dependence of PEM fuel cell performance on catalyst loading , 2004 .

[23]  Eric Irissou,et al.  PEMFC Anode with Very Low Pt Loadings Using Pulsed Laser Deposition , 2003 .

[24]  Viral S. Mehta,et al.  Review and analysis of PEM fuel cell design and manufacturing , 2003 .

[25]  F. Prinz,et al.  A sharp peak in the performance of sputtered platinum fuel cells at ultra-low platinum loading , 2002 .

[26]  A. John Appleby,et al.  Recent progress in performance improvement of the proton exchange membrane fuel cell (PEMFC) , 2002 .

[27]  Jean St-Pierre,et al.  Low Cost Electrodes for Proton Exchange Membrane Fuel Cells Performance in Single Cells and Ballard Stacks , 1997 .

[28]  Supramaniam Srinivasan,et al.  High performance proton exchange membrane fuel cells with sputter-deposited Pt layer electrodes , 1997 .

[29]  Sanjeev Mukerjee,et al.  Effect of sputtered film of platinum on low platinum loading electrodes on electrode kinetics of oxygen reduction in proton exchange membrane fuel cells , 1993 .

[30]  Charles R. Martin,et al.  Electrode kinetics of oxygen reduction at carbon-supported and unsupported platinum microcrystallite/Nafion® interfaces , 1992 .

[31]  Edson A. Ticianelli,et al.  Methods to Advance Technology of Proton Exchange Membrane Fuel Cells , 1988 .