Mathematical modeling and thermodynamic investigation of the use of two-phase ejectors for work recovery and liquid recirculation in refrigeration cycles.

This paper presents the results of a numerical investigation on the performance of ejector cycles in which the work recovered is used to recirculate liquid through the evaporator. The ejector recirculation cycle, in which the ejector is only used to recirculate liquid and improve evaporator performance, and the standard ejector cycle, in which the ejector can be used to both recirculate liquid and directly unload the compressor, are investigated. The analysis uses a microchannel evaporator and refrigerants R134a, R410A, and CO2. It is seen that fluids that have large throttling loss but gain little benefit from liquid recirculation (CO2) should use the ejector to directly unload the compressor, while fluids that have lower throttling loss but gain significant benefit from liquid recirculation (R134a) should use the ejector to improve evaporator performance through liquid recirculation. It is also seen that the ejector recirculation cycle is better suited for ejector off-design operation.

[1]  Wilbert F. Stoecker,et al.  Industrial Refrigeration Handbook , 1998 .

[2]  José Fernández-Seara,et al.  Experimental evaluation of a cascade refrigeration system prototype with CO2 and NH3 for freezing process applications , 2011 .

[3]  Stefan Elbel,et al.  Historical and present developments of ejector refrigeration systems with emphasis on transcritical carbon dioxide air-conditioning applications , 2011 .

[4]  Predrag Stojan Hrnjak,et al.  Ejector in R410A vapor compression systems with experimental quantification of two major mechanisms of performance improvement: Work recovery and liquid feeding , 2015 .

[5]  Neal Lawrence,et al.  Theoretical and practical comparison of two-phase ejector refrigeration cycles including First and Second Law analysis , 2013 .

[6]  P. Hrnjak,et al.  Charge Minimization in Systems and Components Using Hydrocarbons as a Refrigerant , 2004 .

[7]  W. Stoecker.  Design of thermal systems , 1971 .

[8]  Alan A. Kornhauser,et al.  The Use of an Ejector as a Refrigerant Expander , 1990 .

[9]  Somchai Wongwises,et al.  Experimental investigation on the performance of the refrigeration cycle using a two-phase ejector as an expansion device , 2004 .

[10]  Laizai Tan,et al.  Experimental evaluation of an ejector as liquid re-circulator in a falling-film water chiller , 2014 .

[11]  Predrag Stojan Hrnjak,et al.  Experimental validation of a prototype ejector designed to reduce throttling losses encountered in transcritical R744 system operation , 2008 .

[12]  J. C. Chen.  Correlation for Boiling Heat Transfer to Saturated Fluids in Convective Flow , 1966 .

[13]  Gene Culver,et al.  Chapter 11. Heat Exchangers , 1998 .

[14]  P. Hrnjak,et al.  R-744 gas cooler model development and validation , 2001 .

[15]  A. Jacobi,et al.  Air-Side Heat Transfer and Friction Correlations for Flat-Tube Louver-Fin Heat Exchangers , 2009 .

[16]  José Fernández-Seara,et al.  Experimental evaluation of an ejector as liquid re-circulator in an overfeed NH3 system with a plate evaporator , 2011 .

[17]  John R. Thome,et al.  New flow boiling heat transfer model and flow pattern map for carbon dioxide evaporating inside horizontal tubes , 2006 .

[18]  Suresh V. Garimella,et al.  Refrigerant flow boiling heat transfer in parallel microchannels as a function of local vapor quality , 2008 .

[19]  Trond Andresen,et al.  Experimental and numerical investigation of the influence of the two-phase ejector geometry on the performance of the R744 heat pump , 2012 .

[20]  N. Hewitt,et al.  Composition shift in liquid-recirculation refrigerating systems: an experimental investigation for the pure fluid R134a and the mixture R32/134a , 1999 .

[21]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[22]  Predrag Stojan Hrnjak,et al.  CO2 and R410A flow boiling heat transfer, pressure drop, and flow pattern at low temperatures in a horizontal smooth tube , 2007 .

[23]  Sven Försterling,et al.  Multi-ejector concept for R-744 supermarket refrigeration , 2014 .

[24]  Neal Lawrence,et al.  Experimental investigation of a two-phase ejector cycle suitable for use with low-pressure refrigerants R134a and R1234yf , 2014 .

[25]  P. Hrnjak,et al.  Charge Reduction Potentials of Several Refrigerants Based on Experimentally Validated Micro-Channel Heat Exchangers Performance and Charge Model , 2012 .

[26]  Sergio Marinetti,et al.  Experimental analysis of a new method for overfeeding multiple evaporators in refrigeration systems , 2014 .

[27]  N. Lawrence,et al.  Numerical Investigation of the Effect of Microchannel Evaporator Design on the Performance of Two-Phase Ejector Automotive Air Conditioning Cycles , 2015 .

[28]  L. Friedel.  Improved Friction Pressure Drop Correlation for Horizontal and Vertical Two-Phase Pipe Flow , 1979 .