Life-Cycle Greenhouse Gas Emissions of Materials Used in Road Construction

This paper provides a comprehensive summary of greenhouse gas (GHG) emissions factors for producing asphalt concrete (referred to as “asphalt”) and portland cement concrete (referred to as “concrete”) pavements. Life-cycle emissions factors are provided for the key components of upstream emissions. GHG components included carbon dioxide (CO2), methane, and nitrous oxide, as well as the oxidation of nonmethane, nonethane volatile organic compounds and carbon monoxide to CO2. The approach described in this paper enabled the evaluation of emissions from hot-mix, warm-mix, and cold-mix asphalts with assumptions on heating requirements for each. The sources used for the emissions factors were derived from existing sources and models, and a key contribution was the synthesis of these factors for ready use by transportation agencies. Results of the comparison of hot-mix asphalt, warm-mix asphalt, and concrete revealed that warm-mix asphalt might have had as little as 34% of the life-cycle GHG emissions of concrete and 76% of those of hot-mix asphalt. Substitution of fly ash for 25% of the cement in concrete reduced global warming potential by 22%.

[1]  Emad Kassem,et al.  A Method for Predicting Asphalt Mixture Compactability and Its Influence on Mechanical Properties , 2009 .

[2]  Rajib B. Mallick,et al.  A laboratory study on CO2 emission from asphalt binder and its reduction with the use of warm mix asphalt , 2009 .

[3]  Brian D Prowell,et al.  Warm-Mix Asphalt: European Practice , 2008 .

[4]  G. M. Davis.  The Department of Transportation , 1970 .

[5]  Mark A. Delucchi,et al.  A Lifecycle Emissions Model (LEM): Lifecycle Emissions from Transportation Fuels, Motor Vehicles, Transportation Modes, Electricity Use, Heating and Cooking Fuels, and Materials , 2003 .

[6]  Krishna Prapoorna Biligiri,et al.  Modeling climate change impacts of pavement production and construction , 2010 .

[7]  Michael Wang,et al.  Allocation of energy use in petroleum refineries to petroleum products , 2004 .

[8]  J. Speight.  The Chemistry and Technology of Petroleum , 1980 .

[9]  M. Miller.  Agency , 2010 .

[10]  Michael Q. Wang.  GREET 1.5 - transportation fuel-cycle model - Vol. 1 : methodology, development, use, and results. , 1999 .

[11]  John A. Gambatese,et al.  Energy Consumption of Asphalt and Reinforced Concrete Pavement Materials and Construction , 2005 .

[12]  N S Erlbaum.  APPLICATION OF CENSUS DATA TO TRANSPORTATION PLANNING AT NEW YORK STATE DEPARTMENT OF TRANSPORTATION , 1997 .

[13]  Richard Lorch,et al.  Construction materials and the environment , 1990 .

[14]  William T. Choate,et al.  Energy and Emission Reduction Opportunities for the Cement Industry , 2003 .

[15]  Anthony J. Buonicore,et al.  Air Pollution Engineering Manual , 1992 .

[16]  Ye Wu,et al.  Development and applications of GREET 2.7 -- The Transportation Vehicle-CycleModel. , 2006 .

[17]  Concrete Batching.  Emission Factor Documentation for AP-42 Section 11.12 , 2006 .

[18]  I. Palou-Rivera,et al.  Updated estimation of energy efficiencies of U.S. petroleum refineries. , 2008 .

[19]  M. Q. Wang,et al.  GREET 1.0 -- Transportation fuel cycles model: Methodology and use , 1996 .

[20]  E Ray Brown.  DENSITY OF ASPHALT CONCRETE - HOW MUCH IS NEEDED? , 1990 .