Machine design and processing considerations for the 3D plotting of thermoplastic scaffolds

3D plotting by micro-extrusion is a promising layer-wise fabrication method for the production of scaffolds in thermoplastic polymers. It is a solvent-free direct technique which permits extensive control over geometry and porosity. This paper highlights the complications that arise when using this technique for the processing of thermally sensitive polymers. It has been noted that the material is subject to extensive thermal load during processing, which may result in degradation by chain scission. This negatively affects scaffold (mechanical) properties as well as predictability and repeatability of the fabrication technique. A rationale is offered as to the main causes of this thermally induced degradation during processing and tentative ideas towards a solution are equally put forward.

[1]  Minna Kellomäki,et al.  A review of rapid prototyping techniques for tissue engineering purposes , 2008, Annals of medicine.

[2]  C. Laurencin,et al.  Biodegradable polymers as biomaterials , 2007 .

[3]  A Ahluwalia,et al.  Microsyringe-based deposition of two-dimensional and three-dimensional polymer scaffolds with a well-defined geometry for application to tissue engineering. , 2002, Tissue engineering.

[4]  C. V. van Blitterswijk,et al.  Design of porous scaffolds for cartilage tissue engineering using a three-dimensional fiber-deposition technique. , 2004, Biomaterials.

[5]  R. Landers,et al.  Biofunctional rapid prototyping for tissue‐engineering applications: 3D bioplotting versus 3D printing , 2004 .

[6]  Hideto Tsuji,et al.  Poly(lactide) stereocomplexes: formation, structure, properties, degradation, and applications. , 2005, Macromolecular bioscience.

[7]  C A van Blitterswijk,et al.  3D fiber-deposited scaffolds for tissue engineering: influence of pores geometry and architecture on dynamic mechanical properties. , 2006, Biomaterials.

[8]  R. Mohammadikhah,et al.  THERMAL DEGRADATION AND KINETIC ANALYSIS OF PURE POLYGLYCOLIC ACID IN PRESENCE OF HUMID AIR , 2008 .

[9]  Wei Sun,et al.  Precision extruding deposition (PED) fabrication of polycaprolactone (PCL) scaffolds for bone tissue engineering , 2009, Biofabrication.

[10]  Antonios G Mikos,et al.  Strategic directions in tissue engineering. , 2007, Tissue engineering.

[11]  J. Lannutti,et al.  Electrospinning for tissue engineering scaffolds , 2007 .

[12]  A. Södergård,et al.  Properties of lactic acid based polymers and their correlation with composition , 2002 .

[13]  C. V. van Blitterswijk,et al.  Integrating novel technologies to fabricate smart scaffolds , 2008, Journal of biomaterials science. Polymer edition.

[14]  B. Eppley,et al.  The Effect of High Temperature Intraoperative Molding on Bioabsorbable PLLA-PGA Craniofacial Fixation , 2006, The Journal of craniofacial surgery.

[15]  Paul Kiekens,et al.  Biopolymers: overview of several properties and consequences on their applications. , 2002 .

[16]  Scott J Hollister,et al.  Scaffold engineering: a bridge to where? , 2009, Biofabrication.

[17]  Wei Sun,et al.  Fabrication of three-dimensional polycaprolactone/hydroxyapatite tissue scaffolds and osteoblast-scaffold interactions in vitro. , 2007, Biomaterials.

[18]  Hideto Tsuji,et al.  Enhanced thermal stability of poly(lactide)s in the melt by enantiomeric polymer blending , 2003 .

[19]  C. M. Agrawal,et al.  Sterilization, toxicity, biocompatibility and clinical applications of polylactic acid/polyglycolic acid copolymers. , 1996, Biomaterials.

[20]  Dong-Woo Cho,et al.  Fabrication of a SFF-based three-dimensional scaffold using a precision deposition system in tissue engineering , 2008 .

[21]  Rainer Schmelzeisen,et al.  Fabrication of soft tissue engineering scaffolds by means of rapid prototyping techniques , 2002 .