论文信息 - Introduction to the OPTIMAT BLADES project - 字舞流文

Introduction to the OPTIMAT BLADES project

A. G. Dutton | C. Kensche | Povl Brøndsted | A. G. Dutton | A. M. van Wingerde | Theodore P. Philippidis | R. P. L. Nijssen | A. M. van Wingerde | Povl Brøndsted | J. J. Heijdra | D.R.V. van Delft | L.G.J. Janssen | C. Kensche | T. K. Jacobsen | T. Philippidis | C. Kensche | T. Jacobsen | A. Dutton | P. Brøndsted | L.G.J. Janssen | T. K. Jacobsen | R. Nijssen | A. V. Wingerde | D. V. Delft | L. Janssen | J. Heijdra

[1] J. Whitney,et al. Design and Fabrication of Tubular Specimens for Composite Characterization , 1972 .

[2] A. A. Ten Have. WISPER and WISPERX Final definition of two standardised fatigue loading sequences for wind turbine blades , 1992 .

[3] Donald F. Adams,et al. An experimental investigation of the biaxial strength of IM6/3501-6 carbon/epoxy cross-ply laminates using cruciform specimens , 2002 .

[4] John F. Mandell,et al. Spectrum Fatigue Lifetime and Residual Strength for Fiberglass Laminates , 2002 .

[5] A. M. van Wingerde,et al. Alternative fatigue lifetime prediction formulations for variable amplitude loading , 2002 .

[6] Kenji Oguni,et al. A Micromechanical failure model for unidirectional fiber reinforced composites , 2001 .

[7] Gunner Chr. Larsen,et al. Fundamentals for remote structural health monitoring of wind turbine blades - a preproject , 2002 .

[8] L. J. Bond,et al. Condition monitoring techniques for composite wind turbine blades : Review of Progress in Quantitative Nondestructive Evaluation, Brunswick, Maine (United States), 28 Jul.– 2 Aug. 1991), Vol. 11B, pp. 1647–1654. Edited by D.O. Thompson and D.E. Chimenti. Plenum Press (1992) , 1994 .

[9] Woonbong Hwang,et al. Failure of carbon/epoxy composite tubes under combined axial and torsional loading 1. Experimental results and prediction of biaxial strength by the use of neural networks , 1999 .

[10] Karl Schulte,et al. Non-destructive testing of FRP by d.c. and a.c. electrical methods , 2001 .

[11] A. Lystrup,et al. Fatigue of Materials and Components for Wind Turbine Rotor Blades , 1996 .

[12] Anindya Ghoshal,et al. Structural health monitoring techniques for wind turbine blades , 2000 .

[13] Douglas S. Cairns,et al. SELECTION OF FIBERGLASS MATRIX RESINS FOR INCREASED TOUGHNESS AND ENVIRONMENTAL RESISTANCE IN WIND TURBINE BLADES , 2000 .

[14] A. G. Dutton,et al. Acoustic Emission Monitoring of Small Wind Turbine Blades , 2002 .

[15] Herbert J. Sutherland,et al. On the Fatigue Analysis of Wind Turbines , 1999 .

[16] P. D. Soden,et al. Biaxial test results for strength and deformation of a range of E-glass and carbon fibre reinforced composite laminates: failure exercise benchmark data , 2002 .

[17] G. Winkel,et al. Fatigue behaviour of fibreglass wind turbine blade material under variable amplitude loading , 1997 .

[18] Ying Shan,et al. Environmental fatigue behavior and life prediction of unidirectional glass–carbon/epoxy hybrid composites , 2001 .

[19] T. Adam,et al. Life prediction for fatigue of T800/5245 carbon-fibre composites: I. Constant-amplitude loading , 1994 .

[20] Herbert J. Sutherland,et al. Effects of Materials Parameters and Design Details on the Fatigue of Composite Materials for Wind Turbine Blades , 1999 .