Evaluation of Shear Crack Width in I-Shaped Prestressed Reinforced Concrete Beams

Recently, Prestressed Reinforced Concrete (PRC) has been accepted as a reasonable structural member that permits cracking. A PRC member is a visible design alternative to either reinforced concrete (RC) or fully prestressed concrete (PC). In Japan, PRC has been widely used for bridge structures because it is economical. PRC members are generally designed to allow cracking under full service loads. Flexural cracking in PRC beams has been already studied and the flexural crack width can be accurately predicated by equations available in the present codes (ACI, CEB-FIP, JSCE, etc.). On the other hand, shear cracking behavior in PRC members is barely understood. The objective of the present study is, therefore, to experimentally explore the shear cracking behavior of PRC beams. Three I-shaped RC and four I-shaped PRC beams were tested under four-point monotonic loading. The experimental program was carried out focusing on the influence of prestressing force, side concrete cover, stirrup spacing, bond characteristics of stirrup and the amount of longitudinal reinforcement on shear crack width. The study revealed that the prestressing force significantly reduced shear crack width in PRC beams as compared to RC beams. In addition, an equation was proposed to calculate shear crack width in RC and PRC members. The proposed formula for shear crack width shows better correlation between calculated values and experimental data than the other formulae.

[1]  Hiroshi MUTSUYOSHI,et al.  CONTROL OF DIAGONAL CRACKING IN PARTIALLY PRESTRESSED CONCRETE BEAMS , 2004 .

[2]  P. D. Zararis,et al.  Diagonal Shear Failure and Size Effect in RC Beams without Web Reinforcement , 2001 .

[3]  Yew-Chaye Loo,et al.  Factors Influencing Spacing and Width of Cracks in Reinforced Concrete; New Prediction Formulae , 2004 .

[4]  Young Soo Yoon,et al.  Minimum Shear Reinforcement in Normal, Medium,and High-Strength Concrete Beams , 1996 .

[5]  Perry Adebar,et al.  Side-Face Reinforcement for Flexural and Diagonal Cracking in Large Concrete Beams , 1999 .

[6]  Eakarat Witchukreangkrai,et al.  2122 CONTROL OF DIAGONAL CRACKING IN PARTIALLY PRESTRESSED CONCRETE BEAMS , 2004 .

[7]  Michael P. Collins,et al.  INFLUENCE OF AXIAL TENSION ON THE SHEAR CAPACITY OF REINFORCED CONCRETE MEMBERS , 1989 .

[8]  土木学会コンクリート委員会.  Standard specification for design and construction of concrete structures , 1986 .

[9]  Comite Euro-International du Beton,et al.  CEB-FIP Model Code 1990 , 1993 .

[10]  Prodromos D. Zararis,et al.  Shear Strength and Minimum Shear Reinforcement of Reinforced Concrete Slender Beams , 2003 .

[11]  Byung Hwan Oh,et al.  SHEAR BEHAVIOR OF FULL-SCALE POST-TENSIONED PRESTRESSED CONCRETE BRIDGE GIRDERS , 2004 .

[12]  Robert J. Frosch,et al.  Influence of Beam Size, Longitudinal Reinforcement, and Stirrup Effectiveness on Concrete Shear Strength , 2002 .

[13]  Robert J. Frosch,et al.  Another Look at Cracking and Crack Control in Reinforced Concrete , 1999 .

[14]  Thomas T. C. Hsu,et al.  Stirrup Stresses in Reinforced Concrete Beams , 1990 .

[15]  Tamon Ueda,et al.  DISPLACEMENTS AT SHEAR CRACK IN BEAMS WITH SHEAR REINFORCEMENT UNDER STATIC AND FATIGUE LOADINGS , 1991 .

[16]  Byung Hwan Oh,et al.  New Formulas for Maximum Crack Width and Crack Spacing in Reinforced Concrete Flexural Members , 1987 .

[17]  Gregory C. Frantz,et al.  Transverse Stirrup Spacing in R/C Beams , 1985 .

[18]  Walter H. Dilger,et al.  Control of Fexural Crack Width in Cracked Prestressed Concrete Members , 1992 .