Mobility of Single-Loop N-Bar Linkage With Active/Passive Prismatic Joints

Single-loop N-bar linkages that contain one prismatic joint are common in engineering. This type of mechanism often requires complicated control and, hence, understanding its mobility is very important. This paper presents a systematic study on the mobility of this type of mechanism by introducing the concept of virtual link. It is found that this type of mechanism can be divided into three categories: Class I, Class II, and Class III. For each category, the slide reachable range is cut into different regions: Grashof region, non-Grashof region, and change-point region. In each region, the rotation range of the revolute joint or rotatability of the linkage can be determined based on Ting 's criteria. The characteristics charts are given to describe the rotatability condition. Furthermore, if the prismatic joint is an active joint, the revolvability of the input revolute joint is dependent in non-Grashof region but independent in other regions. If the prismatic joint is a passive joint, the revolvability of the input revolute joint is dependent on the offset distance of the prismatic joint. Two examples are given to demonstrate the presented method. The new method is able to cover all the cases of N-bar planar linkages with one or a set of adjoined prismatic joints. It can also be used to study N-bar open-loop planar robotic mechanisms.

[1]  K. Ting,et al.  Rotatability Laws for N-Bar Kinematic Chains and Their Proof , 1991 .

[2]  Kwun-Lon Ting,et al.  Mobility criteria of single-loop N-bar linkages , 1989 .

[3]  F. Park,et al.  Manipulability of Closed Kinematic Chains , 1998 .

[4]  K. C. Gupta,et al.  Design Considerations for Manipulator Workspace , 1982 .

[5]  Anirvan DasGupta.  Mobility Analysis of a Class of RPSPR Kinematic Chains , 2004 .

[6]  A. K. Mallik.  Mobility Analysis and Type Identification of Four-Link Mechanisms , 1994 .

[7]  Jeffrey C. Trinkle,et al.  Motion planning for planar n-bar mechanisms with revolute joints , 2001, Proceedings 2001 IEEE/RSJ International Conference on Intelligent Robots and Systems. Expanding the Societal Role of Robotics in the the Next Millennium (Cat. No.01CH37180).

[8]  R. S. Khurmi,et al.  Theory of Machines , 1995 .

[9]  Nabil G. Chalhoub,et al.  A STRUCTURAL FLEXIBILITY TRANSFORMATION MATRIX FOR MODELLING OPEN-KINEMATIC CHAINS WITH REVOLUTE AND PRISMATIC JOINTS , 1998 .

[10]  L. D. Aguilera,et al.  A More General Mobility Criterion for Parallel Platforms , 2004 .

[11]  Mobility Analysis of RSSR Mechanisms by Working Volume , 2005 .

[12]  H. Lipkin,et al.  Mobility of Overconstrained Parallel Mechanisms , 2006 .

[13]  K. Ting,et al.  Invariant Link Rotatability of N-Bar Kinematic Chains , 1994 .

[14]  Yung-Way Liu,et al.  On the Rotatability of Spherical N-Bar Chains , 1994 .

[15]  Tsuneo Yoshikawa,et al.  Manipulability of Robotic Mechanisms , 1985 .

[16]  Lin Zhang.  NUMERICAL SIMULATION OF THE THREE DEMENSIONAL FLUID FLOW AND HEAT TRANSFER OF HEAT EXCHANGER TUBES WITH TWISTED-TAPE INSERT , 2005 .

[17]  Kwun-Lon Ting,et al.  Five-Bar Grashof Criteria , 1986 .

[18]  Kwun-Lon Ting,et al.  Workspace and sensitive postures of planar open-loop manipulators , 1991 .

[19]  Jianmin Zhu,et al.  The effects of joint clearance on position and orientation deviation of linkages and manipulators , 2000 .

[20]  Kwun-Lon Ting.  Mobility criteria of geared five-bar linkages , 1994 .

[21]  V. Parenti-Castelli,et al.  Mobility Analysis of the 3-UPU Parallel Mechanism Assembled for a Pure Translational Motion , 2002 .

[22]  Xiaohong Dou,et al.  Branch Identification of Geared Five-Bar Chains , 1996 .

[23]  Arthur G. Erdman,et al.  Synthesis of a Geared N-Bar Linkage , 1971 .

[24]  Ruxu Du,et al.  A New Type of Controllable Mechanical Press: Motion Control and Experiment Validation , 2005 .

[25]  E. Amezua,et al.  A method for the solution of the forward position problems of planar mechanisms with prismatic and revolute joints , 2001 .

[26]  Qinchuan Li,et al.  Mobility Analysis of a Novel 3-5R Parallel Mechanism Family , 2004 .

[27]  K. Y. Tsai,et al.  Trajectory Planning in Joint Space for Mechanical Manipulators , 1993 .

[28]  J. Eddie Baker.  The closure modes of Bennett's twelve-bar planar linkage , 2004 .

[30]  Mathukumalli Vidyasagar,et al.  ALGORITHM FOR GENERATING INERTIA MATRICES OF A CLASS OF N-BAR-LINKAGE ROBOTS. , 1987 .

[31]  Ruxu Du,et al.  The Design of a New Metal Forming Press with Controllable Mechanism , 2003 .

[32]  José María Rico Martínez,et al.  On Mobility Analysis of Linkages Using Group Theory , 2003 .

[33]  B. Bahgat,et al.  The parametric coupler curve equations of an eight link planar mechanism containing revolute and prismatic joints , 1992 .

[34]  Ruxu Du,et al.  On the Mobility of Single Loop N-Bar Linkage With One Prismatic Joint , 2005 .