Flow separation in the inlet valve gap of piston engines

Abstract Separation of the inlet flow in an internal combustion engine around the valve gap is analysed on the basis of data available in the literature as well as on experimental data obtained under steady and unsteady flow conditions with a moving piston at fixed valve lifts. The analysis comprises mass flow rate and pressure drop measurements, surface flow visualization and spatial and temporal distributions of velocity components in the valve gap measured by laser-Doppler anemometry (LDA). The results show that the simple four-mode model widely used in the literature is not sufficient for proper description of the complex flow separation phenomenon. The flow separation is distributed non-uniformly across the valve gap width and around the valve periphery. In the light of these properties, single-point investigations usind LDA or hot-wire anemometry techniques must be criticized. More attention must be paid to proper comparison of results obtained by different authors or by experiment and computational fluid dynamics (CFD). The valve lift and valve geometry alone are not sufficient for proper data comparison and interpretation; the valve location in the engine head must also be taken into account. For time-dependent flow conditions, two additional parameters, crank angle and engine (piston) speed, are very important.

[1]  Cameron Tropea,et al.  Laser Doppler anemometry: recent developments and future challenges , 1995 .

[2]  K. O. Suen,et al.  A Comparison of Cycle-Resolved and Ensemble-Averaged velocity variations in a Diesel Engine , 1989 .

[3]  M. Yianneskis,et al.  Velocity Characteristics of Steady Flows through Engine Inlet Ports and Cylinders , 1988 .

[4]  William G. Agnew,et al.  Fifty years of combustion research at General Motors , 1978 .

[5]  Eiichi Watanabe,et al.  Air Flow through Poppet Inlet Valves - Analysis of Static and Dynamic Flow Coefficients , 1982 .

[6]  T. Fansler,et al.  Cycle-Resolved Laser-Velocimetry Measurements in a Reentrant-Bowl-in-Piston Engine , 1988 .

[7]  F. Durst,et al.  Adaptive optics for IC-engine measurements , 1986 .

[8]  S. S. Wiseall,et al.  Flow measurements in turbomachinery using laser anemometry and holography , 1989 .

[9]  A. Melling,et al.  Flow asymmetry in geometrically symmetric engine head configurations , 1994 .

[10]  Charles A. Amann,et al.  Combustion Modeling in Reciprocating Engines , 1980 .

[11]  J. H. Whitelaw,et al.  Manifold Injection and the Origin of Droplets at the Exit of an Inlet Valve , 1996 .

[12]  C. Arcoumanis,et al.  Valve and In-Cylinder Flow Generated by a Helical Port in a Production Diesel Engine , 1987 .

[13]  Marc-P. Errera,et al.  Three-Dimensional Numerical and Experimental Analysis of In-Cylinder Flow in an Internal Combustion Engine , 1988 .

[14]  R. Adrian,et al.  Instantaneous Planar Measurements of Velocity and Large-Scale Vorticity and Strain Rate in an Engine Using Particle-Image Velocimetry , 1989 .

[15]  Takuji Ishiyama,et al.  Experimental Study on Fuel-Air Mixture Formation and Ignition Process in Diesel Combustion. , 1991 .

[16]  C. Arcoumanis,et al.  Fluid Mechanics of Internal Combustion Engines—a Review* , 1987 .

[17]  P. Witze,et al.  A Critical Comparison of Hot-Wire Anemometry and Laser Doppler Velocimetry for I. C. Engine Applications , 1980 .

[18]  E. S. Taylor,et al.  AIR FLOW Through Intake Valves , 1942 .

[19]  Götz Tippelmann.  A New Method of Investigation of Swirl Ports , 1977 .

[20]  F. Durst,et al.  Fluid dynamically caused cycle-to-cycle variations in piston-driven pipe expansion flows , 1992 .

[21]  Michael Yianneskis,et al.  CHARACTERISTICS OF THE FLOW IN THE VICINITY OF THE INTAKE VALVE OF A DIESEL-ENGINE , 1990 .

[22]  Takeyuki Kamimoto,et al.  Combustion processes in diesel engines , 1991 .

[23]  L. Crawforth,et al.  Quantitative visualization of surface flows on rotating disks , 1994 .

[24]  A. Melling,et al.  Principles and practice of laser-Doppler anemometry , 1976 .

[25]  Hiromitsu Ando,et al.  Concept of lean combustion by barrel-stratification , 1992 .

[26]  Miroslaw Weclas.  The influence of radial positioning accuracy on LDA velocity measurements in a valve gap , 1996 .

[27]  Thomas A. Litzinger,et al.  A study of non-swirling and swirling and their effects on spray flow fields and combustion in an optically-accessible, DI diesel engine , 1990 .

[28]  Bahram Khalighi,et al.  Unsteady-flow velocity measurements around an intake valve of a reciprocating engine , 1987 .

[29]  G. Wigley,et al.  Comparison of diesel-engine inlet-valve flows under steady state and motoring conditions , 1993, Other Conferences.

[30]  F. Durst,et al.  Piston‐driven, unsteady separation at a sudden expansion in a tube: Flow visualization and LDA measurements , 1989 .

[31]  K. O. Suen,et al.  Steady Flow Characteristics of Two Generic Inlet Ports , 1992 .

[32]  A. D. Gosman,et al.  Flow in a Model Engine with a Shrouded Valve-A Combined Experimental and Computational Study , 1985 .

[33]  David L. Harrington,et al.  The Spray Characteristics of Automotive Port Fuel Injection-A Critical Reviews , 1995 .

[34]  Aldo Coghe,et al.  Effects of intake ports on the in-cylinder air motion under steady flow conditions , 1988 .

[35]  Thomas Morel,et al.  Fluid mechanics of combustion systems , 1981 .

[36]  R. Adrian.  Particle-Imaging Techniques for Experimental Fluid Mechanics , 1991 .

[37]  C. Arcoumanis,et al.  Effect of Inlet Parameters on the Flow Characteristics in a Four-Stroke Model Engine , 1982 .

[38]  L. J. Kastner,et al.  Poppet Inlet Valve Characteristics and Their Influence on the Induction Process , 1963 .

[39]  Takeyuki Kamimoto,et al.  Stratification of Swirl Intensity in the Axial Direction for Control of Turbulence Generation During the Compression Stroke , 1991 .

[40]  H. Endres,et al.  Influence of Swirl and Tumble on Economy and Emissions of Multi Valve SI Engines , 1992 .

[41]  P. V. Farrell,et al.  Particle Image Velocimetry Measurements of IC Engine Valve Flows , 1992 .

[42]  J. C. Kent,et al.  Measurement of intake valve/cylinder boundary flows using a multiple orientation hot-wire technique , 1988 .

[43]  Hideo Takahashi,et al.  Characteristics of Diesel Spray with Unsteady and Higher Injection Pressure Using a Rapid Compression Machine , 1991 .

[44]  M. Wȩcłaś,et al.  Some aspects of atomization spectrum analysis on basis of holographic experiments , 1988 .

[45]  M. Yianneskis,et al.  An experimental study of velocity and reynolds stress distributions in a production engine inlet port under steady flow conditions , 1990 .

[46]  Y. J. Lee,et al.  A Review of Holography Applications in Multiphase Flow Visualization Study , 1986 .

[47]  Mark S. Huebler,et al.  A Transient Water Analog of a Dual-Intake-Valve Engine for Intake Flow Visualization and Full-Field Velocity Measurements , 1988 .

[48]  S. R. Mueller,et al.  Observations on the Effects of Intake-Generated Swirl and Tumble on Combustion Duration , 1989 .

[49]  W. C. Reynolds,et al.  Modeling of Fluid Motions in Engines—An Introductory Overview , 1980 .

[50]  A. Melling,et al.  Unsteady Intake Valve Gap Flows , 1995 .

[51]  G. Batchelor,et al.  An Introduction to Fluid Dynamics , 1968 .

[52]  A. Ekchian,et al.  Flow visualization study of the intake process of an internal combustion engine. , 1979 .

[53]  A. F. Bicen,et al.  Steady and Unsteady Airflow Through the Intake Valve of a Reciprocating Engine , 1985 .

[54]  A. Melling,et al.  Combined application of surface flow visualization and laser-Doppler anemometry to engine intake flows , 1993 .

[55]  O. Hadded,et al.  The Development of Scanning LDA for the Measurement of Turbulence in Engines , 1988 .

[56]  Tsutomu Hosokawa,et al.  Flow Visualisation of Process of Producing Induction Swirl using a Water Model , 1986 .

[57]  Cameron Tropea,et al.  Combined Application of Particle Image Velocimetry (PIV) and Laser Doppler Anemometry (LDA) to Swirling Flows Under Compression , 1997 .

[58]  Thomas Morel,et al.  Characterization of Flow Produced by a High-Swirl Inlet Port , 1983 .

[59]  Yeng-Yung Tsui,et al.  Calculation of turbulent flow through engine inlet ports , 1992 .