Optimal Modifications of Gear Tooth Surfaces

62 Management Summary In this paper a new method for the introduction of optimal modifications into gear tooth surfaces—based on the optimal corrections of the profile and diameter of the head cutter, and optimal variation of machine tool settings for pinion and gear finishing—is presented. The goal of these tooth modifications is the achievement of a more favorable load distribution and reduced transmission error. The method is applied to face milled and face hobbed hypoid gears. Corresponding computer programs are developed. By using these programs, the optimal head cutter geometry and the optimal machine tool settings for pinion and gear tooth processing are determined. The influence of tooth errors and misalignments of the mating members on load distribution and transmission error is investigated. The obtained results show that the influence of tooth errors and misalignments on gear performances is significantly reduced by the introduction of optimal tooth modifications.

[1]  Faydor L. Litvin,et al.  Methods of Synthesis and Analysis for Hypoid Gear-Drives of “Formate” and “Helixform”—Part 2. Machine Setting Calculations for the Pinions of Formate and Helixform Gears , 1981 .

[2]  Faydor L. Litvin,et al.  Determination of Settings of a Tilted Head-Cutter for Generation of Hypoid and Spiral Bevel Gears. , 1988 .

[3]  V. Simon.  New type of ground double enveloping worm gear drive , 1989 .

[4]  V. Simon.  Optimal Tooth Modifications for Spur and Helical Gears , 1989 .

[5]  Yi Zhang,et al.  Local Synthesis and Tooth Contact Analysis of Face-Milled Spiral Bevel Gears , 1991 .

[6]  Vilmos Simon.  Load Distribution in Double Enveloping Worm Gears , 1993 .

[7]  F. Litvin,et al.  Gear geometry and applied theory , 1994 .

[8]  Vilmos Simon.  Characteristics of a New Type of Cylindrical Worm-Gear Drive , 1996 .

[9]  Vilmos Simon,et al.  Tooth contact analysis of mismatched hypoid gears , 1996 .

[10]  Chung-Biau Tsay,et al.  MATHEMATICAL MODEL OF SPIRAL BEVEL AND HYPOID GEARS MANUFACTURED BY THE MODIFIED ROLL METHOD , 1997 .

[11]  Hisashi Tamura,et al.  Klingelnberg spiral bevel gears with small spiral angles , 1999 .

[12]  Uwe Gaiser,et al.  The Ultimate Motion Graph , 2000 .

[13]  Vilmos Simon,et al.  Load Distribution in Hypoid Gears , 2000 .

[14]  C. Tsay,et al.  Effects of profile shifted factor and pressure angle on the ZK-type dual-lead worm gear drives , 2001 .

[15]  Márk Lelkes,et al.  Numerical Determination of Cutting Parameters for the Control of Klingelnberg Spiral Bevel Gear Geometry , 2002 .

[16]  Alfonso Fuentes,et al.  Computerized integrated approach for design and stress analysis of spiral bevel gears , 2002 .

[17]  Vilmos Simon.  Optimal Tooth Modifications in Hypoid Gears , 2003 .

[18]  Datong Qin,et al.  Meshing control of the double-enveloping hourglass worm gearing under the conditions of existing the errors and the load , 2004 .

[19]  Vilmos Simon,et al.  Computer Aided Loaded Tooth Contact Analysis in Cylindrical Worm Gears , 2005 .

[20]  Chung-Biau Tsay,et al.  Meshing simulations of the worm gear cut by a straight-edged flyblade and the ZK-type worm with a non-90° crossing angle , 2006 .

[21]  Zhang-Hua Fong,et al.  Fourth-order kinematic synthesis for face-milling spiral bevel gears with modified radial motion (MRM) correction , 2006 .

[22]  Qi Fan.  Computerized Modeling and Simulation of Spiral Bevel and Hypoid Gears Manufactured by Gleason Face Hobbing Process , 2006 .

[23]  Michèle Guingand,et al.  Numerical simulation and optimisation of worm gear cutting , 2006 .

[24]  Vilmos Simon.  Optimal tooth modifications in spiral bevel gears introduced by machine tool setting variation , 2006 .

[25]  Faydor L. Litvin,et al.  Geometry and Investigation of Klingelnberg-Type Worm Gear Drive , 2007 .

[26]  M. Vimercati,et al.  Mathematical model for tooth surfaces representation of face-hobbed hypoid gears and its application to contact analysis and stress calculation , 2007 .

[27]  Vilmos Simon.  The Influence of Gear Hobbing on Worm Gear Characteristics , 2007 .

[28]  Vilmos Simon,et al.  Load Distribution in Spiral Bevel Gears , 2007 .

[29]  Faydor L. Litvin,et al.  Application and Investigation of Modified Helical Gears With Several Types of Geometry , 2007 .

[30]  F. Di Puccio,et al.  An invariant approach for gear generation with supplemental motions , 2007 .

[31]  Faydor L. Litvin,et al.  Design, simulation of meshing, and contact stresses for an improved worm gear drive , 2007 .

[32]  Zhi Wu,et al.  Geometry of Tooth Profile and Fillet of Face-Hobbed Spiral Bevel Gears , 2007 .

[33]  Vilmos Simon,et al.  Computer simulation of tooth contact analysis of mismatched spiral bevel gears , 2007 .

[34]  Vilmos Simon,et al.  Design and Manufacture of Spiral Bevel Gears With Reduced Transmission Errors , 2009 .

[35]  Qi Fan,et al.  Higher-Order Tooth Flank Form Error Correction for Face-Milled Spiral Bevel and Hypoid Gears , 2008 .

[36]  Yi-Pei Shih,et al.  Flank Correction for Spiral Bevel and Hypoid Gears on a Six-Axis CNC Hypoid Generator , 2008 .

[37]  Massimo Guiggiani,et al.  Optimization of the Loaded Contact Pattern in Hypoid Gears by Automatic Topography Modification , 2009 .

[38]  Chung-Biau Tsay,et al.  Mathematical model and worm wheel tooth working surfaces of the ZN-type hourglass worm gear set , 2009 .

[39]  Cheng-Kang Lee,et al.  Manufacturing process for a cylindrical crown gear drive with a controllable fourth order polynomial function of transmission error , 2009 .