A Combined In-Mold Decoration and Microcellular Injection Molding Method for Preparing Foamed Products with Improved Surface Appearance

A combined in-mold decoration and microcellular injection molding (IMD/MIM) method by integrating in-mold decoration injection molding (IMD) with microcellular injection molding (MIM) was proposed in this paper. To verify the effectiveness of the IMD/MIM method, comparisons of in-mold decoration injection molding (IMD), conventional injection molding (CIM), IMD/MIM and microcellular injection molding (MIM) simulations and experiments were performed. The results show that compared with MIM, the film flattens the bubbles that have not been cooled and turned to the surface, thus improving the surface quality of the parts. The existence of the film results in an asymmetrical temperature distribution along the thickness of the sample, and the higher temperature on the film side leads the cell to move toward it, thus obtaining a cell-offset part. However, the mechanical properties of the IMD/MIM splines are degraded due to the presence of cells, while specific mechanical properties similar to their solid counterparts are maintained. Besides, the existence of the film reduces the heat transfer coefficient of the film side so that the sides of the part are cooled asymmetrically, causing warpage.

[1]  Wei Hua Guo,et al.  Effects of Nano-CaCO3 Content on the Crystallization, Mechanical Properties, and Cell Structure of PP Nanocomposites in Microcellular Injection Molding , 2018, Polymers.

[2]  S. Chen,et al.  Improvement on the surface quality of microcellular injection molded parts using microcellular co-injection molding with the material combinations of PP and PP-GF , 2017, International Journal of Plastics Technology.

[3]  Chul B. Park,et al.  Study of the foaming mechanisms associated with gas counter pressure and mold opening using the pressure profiles , 2017 .

[4]  Guoqun Zhao,et al.  A novel gas-assisted microcellular injection molding method for preparing lightweight foams with superior surface appearance and enhanced mechanical performance , 2017 .

[5]  Cheng-Long Xiao,et al.  Development and application of rapid thermal cycling molding with electric heating for improving surface quality of microcellular injection molded parts , 2016 .

[6]  Guoqun Zhao,et al.  Bubble morphological evolution and surface defect formation mechanism in the microcellular foam injection molding process , 2015 .

[7]  Guoqun Zhao,et al.  Research on formation mechanisms and control of external and inner bubble morphology in microcellular injection molding , 2015 .

[8]  L. Turng,et al.  A novel method of producing lightweight microcellular injection molded parts with improved ductility and toughness , 2015 .

[9]  Hanxiong Huang,et al.  Development of a rapid thermal cycling molding with electric heating and water impingement cooling for injection molding applications , 2014 .

[10]  Kunyu Zhang,et al.  Co-Injection Molded New Green Composites from Biodegradable Polyesters and Miscanthus Fibers , 2014 .

[11]  Guoqun Zhao,et al.  Influence of relative low gas counter pressure on melt foaming behavior and surface quality of molded parts in microcellular injection molding process , 2014 .

[12]  Shih-Jung Liu,et al.  Factors Influencing the Warpage in In-Mold Decoration Injection Molded Composites , 2013 .

[13]  S. Chen,et al.  The effects of gas counter pressure and mold temperature variation on the surface quality and morphology of the microcellular polystyrene foams , 2013 .

[14]  Rean-Der Chien,et al.  Effects of insert film on asymmetric mold temperature and associated part warpage during in-mold decoration injection molding of PP parts , 2013 .

[15]  Rean-Der Chien,et al.  Structure and mechanical properties of polystyrene foams made through microcellular injection molding via control mechanisms of gas counter pressure and mold temperature , 2012 .

[16]  Guoqun Zhao,et al.  Research and application of a new rapid heat cycle molding with electric heating and coolant cooling to improve the surface quality of large LCD TV panels , 2011 .

[17]  Jungjoo Lee,et al.  A novel method for improving the surface quality of microcellular injection molded parts , 2011 .

[18]  L. Turng,et al.  Improving surface quality of microcellular injection molded parts through mold surface temperature manipulation with thin film insulation , 2010 .

[19]  Rean-Der Chien,et al.  Variable mold temperature to improve surface quality of microcellular injection molded parts using induction heating technology , 2008 .

[20]  S. Chen,et al.  Study on the thermoforming of PC films used for in-mold decoration , 2008 .

[21]  D. Gethin,et al.  Mechanical properties of polymer films used in in-mould decoration , 2008 .

[22]  S. Cha,et al.  Label behavior property attached on microcellular foamed parts , 2005 .

[23]  Zhongbao Chen,et al.  Quantitative Study of Shrinkage and Warpage Behavior for Microcellular and Conventional Injection Molding , 2005 .

[24]  L. Turng,et al.  Microcellular Injection Molding , 2005 .

[25]  L. Turng,et al.  Development of a Hybrid Solid-Microcellular Co-injection Molding Process , 2004 .

[26]  N. Suh,et al.  A process for making microcellular thermoplastic parts , 1990 .