Modelling and parametric study of an efficient Alpha type Stirling engine performance based on 3D CFD analysis

Abstract As an externally heated engine the Stirling engine has the advantage of being able to efficiently exploit various waste heat sources. Computational fluid dynamic simulation (CFD) for the thermodynamic performance of such engines can provide a powerful tool to predict and improve the design and performance. Despite the advantages of alpha type Stirling engines, there has been very limited published work regarding the use of CFD modelling to improve its performance. This paper, proposed a new methodology combining the thermodynamic model with 3D CFD analysis to investigate the performance of a V-Alpha Type Stirling engine under various operating conditions and design parameters. The thermodynamic model of an alpha type Stirling engine has been developed using non-ideal adiabatic analysis and validated against experimental measurements of the engine prototype. A 3D CFD model was then developed and the results, compared to the those of the thermodynamic model, showed good agreement in predicting the indicated power. The CFD model was used to carry out a parametric study to investigate the effects of various design parameters and operating conditions such as, regenerator porosity, charge pressure, matrix wire diameter, dead volume and hot/cold ends temperatures on the engine performance in terms of power output through predicting the PV diagram of the engine. Results showed that maximum power can be achieved by increasing the porosity up to 80% and the wire matrix diameter to 0.02 mm at a temperature of the hot and cold sides at 600 °C and 20 °C respectively. Further decreasing of the cold end temperature to −20 °C can produce 162 W. For the heater and the cooler volumes, it was found that a height of 140 mm produced the highest engine power output of 170 W. This work highlights the potential of using CFD modelling to improve the design parameters and operating conditions to enhance the performance of alpha type Stirling engines.

[1]  Mounir B. Ibrahim,et al.  Stirling Convertor Regenerators , 2011 .

[2]  Khamid Mahkamov,et al.  Closure to “Discussion: ‘Design Improvements to a Biomass Stirling Engine Using Mathematical Analysis and 3D CFD Modeling’ ” (2007, ASME J. Energy Resour. Technol., 129, pp. 278, 279, 280) , 2007 .

[3]  Raya Al-Dadah,et al.  Enhanced thermodynamic modelling of a gamma-type Stirling engine , 2016 .

[4]  G. Walker,et al.  Theoretical Performance of Stirling Cycle Engines , 1965 .

[5]  Sassi Ben Nasrallah,et al.  Determination of adequate regenerator for a Gamma-type Stirling engine , 2015 .

[6]  Gang Xiao,et al.  Improved Simple Analytical Model and experimental study of a 100W β-type Stirling engine , 2016 .

[7]  Israel Urieli,et al.  Stirling Cycle Engine Analysis , 1983 .

[8]  John M. Gary,et al.  Calculated Performance of Low-Porosity Regenerators at 4 K with He-4 and He-3 | NIST , 2008 .

[9]  Alain Ferriere,et al.  Thermal model of a dish/Stirling systems , 2009 .

[10]  Henrik Carlsen,et al.  Numerical study on optimal Stirling engine regenerator matrix designs taking into account the effects of matrix temperature oscillations , 2006 .

[11]  J. A. Esnaola,et al.  The thermal non-equilibrium porous media modelling for CFD study of woven wire matrix of a Stirling regenerator , 2015 .

[12]  S. Ben Nasrallah,et al.  Experimental and theoretical investigation of Stirling engine heater: Parametrical optimization , 2015 .

[13]  Mokhtar Bidi,et al.  Optimization of powered Stirling heat engine with finite speed thermodynamics , 2016 .

[14]  Kamaruzzaman Sopian,et al.  Design consideration of low temperature differential double-acting Stirling engine for solar application , 2005 .

[15]  Raya Al-Dadah,et al.  Influence of phase angle and dead volume on gamma-type Stirling engine power using CFD simulation , 2016 .

[16]  J. A. Esnaola,et al.  Experimental and numerical flow investigation of Stirling engine regenerator , 2014 .

[17]  Wen Lih Chen,et al.  An experimental study on the performance of the moving regenerator for a γ-type twin power piston Stirling engine , 2014 .

[18]  Halit Karabulut,et al.  Manufacturing and Testing of a V-Type Stirling Engine , 2000 .

[19]  Frank P. Incropera,et al.  Fundamentals of Heat and Mass Transfer , 1981 .

[20]  D. Gedeon,et al.  Oscillating-Flow Regenerator Test Rig: Hardware and Theory With Derived Correlations for Screens and Felts , 1996 .

[21]  Ennio Macchi,et al.  Experimental and numerical study of a micro-cogeneration Stirling unit under diverse conditions of the working fluid , 2015 .

[22]  Wen Lih Chen,et al.  A numerical analysis on the performance of a pressurized twin power piston gamma-type Stirling engine , 2012 .

[23]  Germilly Barreto,et al.  Modelling of a Stirling engine with parabolic dish for thermal to electric conversion of solar energy , 2017 .

[24]  Charles Harman,et al.  Application of the Direct Method to irreversible Stirling cycles with finite speed , 2002 .

[25]  Wen Lih Chen,et al.  A computational fluid dynamics study on the heat transfer characteristics of the working cycle of a β-type Stirling engine , 2014 .

[26]  Dawei Tang,et al.  Analysis of a high performance model Stirling engine with compact porous-sheets heat exchangers , 2014 .

[27]  K. Mahkamov.  An axisymmetric computational fluid dynamics approach to the analysis of the working process of a solar stirling engine. , 2006 .

[28]  Iskander Tlili,et al.  PERFORMANCE OPTIMIZATION OF STIRLING ENGINES , 2008 .

[29]  Lavinia Grosu,et al.  Losses effect on the performance of a Gamma type Stirling engine , 2016 .

[30]  W. Chen,et al.  A computational fluid dynamics study on the heat transfer characteristics of the working cycle of a low-temperature-differential γ-type Stirling engine , 2014 .

[31]  Iskander Tlili,et al.  Design and performance optimization of GPU-3 Stirling engines , 2008 .

[32]  Wen Lih Chen,et al.  A CFD parametric study on the performance of a low-temperature-differential γ-type Stirling engine , 2015 .

[33]  Joseph A. Araoz,et al.  Numerical simulation for the design analysis of kinematic Stirling engines , 2015 .

[34]  Raya Al-Dadah,et al.  Potentiality of new miniature-channels Stirling regenerator , 2017 .

[35]  Chin-Hsiang Cheng,et al.  Theoretical and experimental study of a 300-W beta-type Stirling engine , 2013 .