Control and Jetting Characteristics of an Innovative Jet Valve With Zoom Mechanism and Opening Electromagnetic Drive

In order to develop jetting technology in LED and microelectronics packaging, an innovative electromagnetic jet valve with zoom mechanism and opening electromagnetic coil is suggested, and an improved method of double voltage drive is applied in the electromagnetic control. It is found that the needle stroke of the new jet valve is increased to 1.3 times, and the needle velocity is raised to 1.8 times, and the temperature of opening electromagnetic coil is lowered to 6.7 °C. The jet valve can successfully jet 4 Pa·s high-viscosity adhesives at room temperature due to the improvement of dynamic characteristics. It will provide a new method for jetting high-viscosity adhesives.

[1]  Liang Cheng,et al.  State Detection of Bond Wires in IGBT Modules Using Eddy Current Pulsed Thermography , 2014, IEEE Transactions on Power Electronics.

[2]  Xiaohui Du,et al.  Design and Experiment of a Jetting Dispenser Driven by Piezostack Actuator , 2013, IEEE Transactions on Components, Packaging and Manufacturing Technology.

[3]  Li Jianping,et al.  Technology development and basic theory study of fluid dispensing - a review , 2004, Proceedings of the Sixth IEEE CPMT Conference on High Density Microsystem Design and Packaging and Component Failure Analysis (HDP '04).

[4]  Horst Clauberg,et al.  Behavior of palladium and its impact on intermetallic growth in palladium-coated Cu wire bonding , 2013 .

[5]  Dong Liang,et al.  A Low-Cost, Normally Closed, Solenoid Valve for Non-Contact Dispensing in the Sub-µL Range , 2013, Micromachines.

[6]  Adalat Nasibov,et al.  Performance Analysis of the CCD Pixel Binning Option in Particle-Image Velocimetry Measurements , 2010, IEEE/ASME Transactions on Mechatronics.

[7]  Won-jong Kim,et al.  Development of a New High-Resolution Angle-Sensing Mechanism Using an RGB Sensor , 2014, IEEE/ASME Transactions on Mechatronics.

[8]  Y. Matsuoka,et al.  Mechanisms of the Anatomically Correct Testbed Hand , 2013, IEEE/ASME Transactions on Mechatronics.

[9]  Han-Xiong Li,et al.  Comparative study of fluid dispensing modeling , 2003 .

[10]  Joonwon Kim,et al.  Development and characterization of a cartridge-type pneumatic dispenser with an integrated backflow stopper , 2009 .

[11]  Han-Xiong Li,et al.  A Simple Model-Based Approach for Fluid Dispensing Analysis and Control , 2007, IEEE/ASME Transactions on Mechatronics.

[12]  Chien-Yi Huang,et al.  Innovative parametric design for environmentally conscious adhesive dispensing process , 2015, J. Intell. Manuf..

[13]  P. Dario,et al.  Magnetically Activated Stereoscopic Vision System for Laparoendoscopic Single-Site Surgery , 2013, IEEE/ASME Transactions on Mechatronics.

[14]  Xiongbiao Chen,et al.  THEORETICAL INVESTIGATION INTO THE PERFORMANCE OF THE ROTARY-SCREW FLUID DISPENSING PROCESS , 2008 .

[15]  Christian Clasen,et al.  Dispensing of rheologically complex fluids: The map of misery , 2012 .

[16]  Chingfu Tsou,et al.  A Silicon-Based LED Packaging Substrate With an Island Structure for Phosphor Encapsulation Shaping , 2015, IEEE Transactions on Components, Packaging and Manufacturing Technology.

[17]  Junfeng Xiao,et al.  Experimental study on high viscosity fluid micro-droplet jetting system , 2010 .

[18]  Xiang Ren,et al.  Modeling of pneumatic valve dispenser for printing viscous biomaterials in additive manufacturing , 2014 .

[19]  Manos M. Tentzeris,et al.  Inkjet-printed antennas, sensors and circuits on paper substrate , 2013 .