Design of a new lithium ion battery test cell for in-situ neutron diffraction measurements

Abstract This paper introduces a new cell design for the construction of lithium ion batteries with conventional electrochemical performance whilst allowing in situ neutron diffraction measurement. A cell comprising of a wound cathode, electrolyte and anode stack has been prepared. The conventional hydrogen-containing components of the cell have been replaced by hydrogen-free equivalents. The electrodes are fabricated using a PTFE binder, the electrolyte consists of deuterated solvents which are supported in a quartz glass fibre separator. Typical battery performance is reported using the hydrogen-free components with a specific capacity of 140 mA h g −1 being observed for LiFePO 4 at a rate of 0.2 C. Neutron diffraction patterns of full cells were recorded with phase change reactions monitored. When aluminium packaging was used a better signal to noise ratio was obtained. The obtained atomic positions and lattice parameters for all cells investigated were found to be consistent with parameters refined from the diffraction pattern of a powder of the pure electrode material. This paper highlights the pertinent points in designing cells for these measurements and addresses some of the problems.

[1]  Kristina Edström,et al.  A neutron diffraction cell for studying lithium-insertion processes in electrode materials , 1998 .

[2]  Mark A. Rodriguez,et al.  Simultaneous in situ-neutron diffraction studies of the anode and cathode in a lithium-ion cell , 2003 .

[3]  Neeraj Sharma,et al.  Structural changes in a commercial lithium-ion battery during electrochemical cycling: An in situ neutron diffraction study , 2010 .

[4]  M. Armand,et al.  Issues and challenges facing rechargeable lithium batteries , 2001, Nature.

[5]  Gavin Vaughan,et al.  In situ X-ray diffraction techniques as a powerful tool to study battery electrode materials , 2002 .

[6]  John B. Goodenough,et al.  Effect of Structure on the Fe3 + / Fe2 + Redox Couple in Iron Phosphates , 1997 .

[7]  H. Berg,et al.  The LiMn2O4 to λ-MnO2 phase transition studied by in situ neutron diffraction , 2001 .

[8]  Neeraj Sharma,et al.  In situ neutron powder diffraction studies of lithium-ion batteries , 2012, Journal of Solid State Electrochemistry.

[9]  K. S. Nanjundaswamy,et al.  Phospho‐olivines as Positive‐Electrode Materials for Rechargeable Lithium Batteries , 1997 .

[10]  N. Sharma,et al.  Direct evidence of concurrent solid-solution and two-phase reactions and the nonequilibrium structural evolution of LiFePO4. , 2012, Journal of the American Chemical Society.

[11]  K. Edström,et al.  3D lithium ion batteries{from fundamentals to fabrication , 2011 .

[12]  Josh Thomas,et al.  Neutron diffraction study of electrochemically delithiated LiMn2O4 spinel , 1999 .

[13]  P. Novák,et al.  A novel electrochemical cell for in situ neutron diffraction studies of electrode materials for lithium-ion batteries , 2008 .

[14]  Neeraj Sharma,et al.  Time-Dependent in-Situ Neutron Diffraction Investigation of a Li(Co0.16Mn1.84)O4 Cathode , 2011 .

[15]  Neeraj Sharma,et al.  In-situ neutron diffraction study of the MoS2 anode using a custom-built Li-ion battery , 2011 .

[16]  J. Dahn,et al.  Electrochemical and In Situ X‐Ray Diffraction Studies of Lithium Intercalation in Li x CoO2 , 1992 .

[17]  Petr Novák,et al.  In situ neutron diffraction study of Li insertion in Li4Ti5O12 , 2010 .

[18]  John O. Thomas,et al.  Lithium extraction/insertion in LiFePO4: an X-ray diffraction and Mossbauer spectroscopy study , 2000 .

[19]  Neeraj Sharma,et al.  Br‐Doped Li4Ti5O12 and Composite TiO2 Anodes for Li‐ion Batteries: Synchrotron X‐Ray and in situ Neutron Diffraction Studies , 2011 .