Suspension HVOF Spraying of Reduced Temperature Solid Oxide Fuel Cell Electrolytes

Metal-supported solid oxide fuel cells (SOFCs) composed of a Ce0.8Sm0.2O2−δ (SDC) electrolyte layer and Ni-Ce0.8Sm0.2O2−δ (Ni-SDC) cermet anode were fabricated by suspension thermal spraying on Hastelloy × substrates. The cathode, a Sm0.5Sr0.5CoO3 (SSCo)-SDC composite, was screen-printed and fired in situ. The anode was produced by suspension plasma spraying (SPS) using an axial injection plasma torch. The SDC electrolyte was produced by high-velocity oxy-fuel (HVOF) spraying of liquid suspension feedstock, using propylene fuel (DJ-2700). The emerging technology of HVOF suspension spraying was explored here to produce thin and low-porosity electrolytes in an effort to develop a cost-effective and scalable fabrication technique for high-performance, metal-supported SOFCs. In-flight particle temperature and velocity were measured for a number of different gun operating conditions and standoff distances and related to the resulting microstructures. At optimized conditions, this approach was found to limit material decomposition, enhance deposition efficiency, and reduce defect density in the resulting coating, as compared to previous results reported with SPS. Produced button cells showed highly promising performance with a maximum power density (MPD) of 0.5 W cm−2 at 600 °C and above 0.9 W cm−2 at 700 °C, with humidified hydrogen as fuel and air as oxidant. The potential of this deposition technique to scale-up the substrate size to 50 × 50 mm was demonstrated.

[1]  R. Maric,et al.  NiO–YSZ cermets supported low temperature solid oxide fuel cells , 2006 .

[2]  S. Sodeoka,et al.  Thermal and mechanical properties of ZrO2-CeO2 plasma-sprayed coatings , 1997 .

[3]  C. Moreau,et al.  Mechanical and Thermal Transport Properties of Suspension Thermal-Sprayed Alumina-Zirconia Composite Coatings , 2007, International Thermal Spray Conference.

[4]  Zhenwei Wang,et al.  Thermal plasma spraying for SOFCs: Applications, potential advantages, and challenges , 2007 .

[5]  Thierry Chartier,et al.  Suspension and solution plasma spraying of finely structured layers: potential application to SOFCs , 2007 .

[6]  Robert Vaßen,et al.  Plasma_sprayed components for SOFC applications , 2006 .

[7]  A. Duckett,et al.  Development of metal supported solid oxide fuel cells for operation at 500–600 °C , 2004 .

[8]  Nigel P. Brandon,et al.  Development of metal supported solid oxide fuel cells for operation at 500–600 °C , 2004 .

[9]  Rudolf Henne,et al.  Solid Oxide Fuel Cells: A Challenge for Plasma Deposition Processes , 2007 .

[10]  M. Inaba,et al.  Effects of mixed conduction on the open-circuit voltage of intermediate-temperature SOFCs based on Sm-doped ceria electrolytes , 2005 .

[11]  E. Ivers-Tiffée,et al.  Materials and technologies for SOFC-components , 2001 .

[12]  Rob Hui,et al.  Suspension Plasma Spraying of Intermediate Temperature SOFC Components Using an Axial Injection DC Torch , 2007 .

[13]  Rainer Gadow,et al.  High-Velocity Suspension Flame Spraying (HVSFS), a new approach for spraying nanoparticles with hypersonic speed , 2006 .

[14]  Zhenwei Wang,et al.  Dynamic evaluation of low-temperature metal-supported solid oxide fuel cell oriented to auxiliary power units , 2008 .