Microstructure and mechanical properties of a large billet of spray formed Al–Zn–Mg–Cu alloy with high Zn content

Abstract In this study, a large billet of Al–12Zn–2.4Mg–1.1Cu–0.5Ni–0.2Zr alloy was prepared by spray deposition technique, the billet was subsequent processed by hot extrusion, solid solution treatment at 758 K and aging at 393 K for 20 h. The aged alloy was then subjected to tensile testing, it was shown that yield strength, tensile strength and elongation rate of the alloy reached 689 MPa, 750 MPa and 11%, respectively. The composition, microstructure and fracture characteristics of the tensile sample were explored by EDS (energy dispersive spectrometer), optical microscopy (OM), transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. A spherical morphology of the primary α-phase was observed in the spray-deposited Al alloy, dispersed and fine-scale L1 2 –Al 3 Zr phases, GPII zones and η′ precipitates, were also evident in the microstructure of the aged alloy. Fracture analysis of the tensile sample exhibited transgranular fractographic features. We suggest that precipitate-phase hardening and solid solution strengthening were responsible for reinforcing of the spray-deposited alloy.

[1]  X. Z. Li,et al.  GP-zones in Al–Zn–Mg alloys and their role in artificial aging , 2001 .

[2]  Hongwei Liu,et al.  Microstructure and mechanical properties of spray-deposited Al–10.8Zn–2.8Mg–1.9Cu alloy after two-step aging treatment at 110 and 150 °C , 2007 .

[3]  T. Eden,et al.  Hardening mechanisms of spray formed Al–Zn–Mg–Cu alloys with scandium and other elemental additions , 2006 .

[4]  Hongwei Liu,et al.  Microstructure and mechanical properties of spray-deposited Al–Zn–Mg–Cu alloy , 2007 .

[5]  S. Jahromi.  Creep behavior of spray-cast 7XXX aluminum alloy , 2002 .

[6]  J. Gjønnes,et al.  An electron microscope investigation of the microstructure in an aluminium-zinc-magnesium alloy , 1970 .

[7]  Timothy J. Eden,et al.  Mesoscopic structure control of spray formed high strength Al–Zn–Mg–Cu alloys , 2005 .

[8]  J. Gjønnes,et al.  Effect of predeformation and preaging at room temperature in Al–Zn–Mg–(Cu,Zr) alloys , 2001 .

[9]  K. Stiller,et al.  Investigation of fine scale precipitates in Al–Zn–Mg alloys after various heat treatments , 2002 .

[10]  K. Ohtera,et al.  An intermediate phase appearing in Ll2-Al3Zr to DO23-Al3Zr phase transformation of rapidly solidified Al-Zr alloys , 1996 .

[11]  Xiaoqing He,et al.  Effect of heat treatment on the microstructure and mechanical properties of the spray-deposited Al–10.8Zn–2.8Mg–1.9Cu alloy , 2008 .

[12]  T. Langdon,et al.  Influence of ECAP on precipitate distributions in a spray-cast aluminum alloy , 2005 .

[13]  Alfred Cerezo,et al.  Early-stage precipitation in Al-Zn-Mg-Cu alloy (7050) , 2004 .

[14]  K. Stiller,et al.  Investigation of precipitation in an Al–Zn–Mg alloy after two-step ageing treatment at 100° and 150°C , 1999 .

[15]  N. Gao,et al.  Microstructural evolution in a spray-cast aluminum alloy during equal-channel angular pressing , 2005 .

[16]  X. Z. Li,et al.  HREM study and structure modeling of the η′ phase, the hardening precipitates in commercial Al–Zn–Mg alloys , 1999 .