Microstructure of AuSn Wafer Bonding for RF-MEMS Packaging

RF-MEMS is one of the most potential applications for MEMS products. Eutectic solder wafer bonding is one of the attractive methods for RF-MEMS wafer level packaging. A process of gold-tin hermetical wafer bonding was developed in SAIT, Korean. Different UBM systems and thin films of gold-tin were deposited on cap wafer, RF-MEMS device wafer and substrate wafer (if needed). The bonding was performed in N2 ambience with pressure. The cross section of bonding layer had been studied using SEM/EDAX. The thickness of bonding layer is uniform, ranging from 5mum to 7mum. Pretreatment is important to obtain good adhesion and successful microstructure. Voids could be detected without ashing. Optimal process, such as plasma cleaning, would eliminate these voids. There existed different regions in the bonding layer due to inter-diffusion between Au-Sn and other elements. Different intermetallic formed at the bonding layer. The compositions of the intermetallic was identified by EDAX and analyzed according to the Au-Sn phase diagram. The microstructures of the bonding layer are similar for different bonding temperatures in experiments, which indicates lower bonding temperature can get the same hermetical sealing. Typically, there are Au rich layer, AuSn IMC layer and Sn/Au-Ni-Ti layer in the bonding layer between cap wafer and substrate wafer, while there are Au layer, Au-Sn-Ni compound layer in the bonding layer between device wafer and substrate wafer. From the EDAX analysis, different intermetallic compound (IMC) can be identified as AuSn2, AuSn and other composition. Hermetical and shear strength test were performed for as-bonded dice. The test results indicated there is little difference among different bonding process. Fracture surfaces after shear test were investigated as well. The fracture was inside Au-Sn IMC. It indicates the UBM selected is suitable for application. Reliability test was also performed

[1]  Ieee Robotics.  MEMS 2001 : the 14th IEEE International Conference on Micro Electro Mechanical Systems : Interlaken, Switzerland, January 21-25, 2001 : technical digest , 2001 .

[2]  K. Boustedt,et al.  Fundamental requirements on MEMS packaging and reliability , 2002, 2002 Proceedings. 8th International Advanced Packaging Materials Symposium (Cat. No.02TH8617).

[3]  H. Reichl,et al.  Overview and development trends in the field of MEMS packaging , 2001, Technical Digest. MEMS 2001. 14th IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.01CH37090).

[4]  Ken Gilleo,et al.  MEMS packaging issues and materials , 2000 .

[5]  L.P.B. Katehi,et al.  Fabrication and accelerated hermeticity testing of an on-wafer package for RF MEMS , 2004, IEEE Transactions on Microwave Theory and Techniques.

[6]  A. Przekwas,et al.  Flip-chip hermetic packaging of RF MEMS , 2001, 2001 Microelectromechanical Systems Conference (Cat. No. 01EX521).

[7]  K. Najafi,et al.  Localized silicon fusion and eutectic bonding for MEMS fabrication and packaging , 1998, Journal of Microelectromechanical Systems.

[8]  M. Fanciulli,et al.  Oxidation and reduction kinetics of eutectic SnPb, InSn and AuSn: a knowledge base for fluxless solder bonding applications , 1997, 1997 Proceedings 47th Electronic Components and Technology Conference.

[9]  Chin C. Lee,et al.  AuSn alloy phase diagram and properties related to its use as a bonding medium , 1993 .

[10]  C.C. Lee,et al.  A fluxless process of producing tin-rich gold-tin joints in air , 2004, IEEE Transactions on Components and Packaging Technologies.

[11]  H. Okada,et al.  Room temperature vacuum sealing using surface activated bonding method , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[12]  Douglas G. Ivey,et al.  Microstructural characterization of Au/Sn solder for packaging in optoelectronic applications , 1998 .

[13]  Qian Wang,et al.  A low temperature, hermetic wafer level packaging method for RF MEMS switch , 2005, Proceedings Electronic Components and Technology, 2005. ECTC '05..

[14]  Gabriel M. Rebeiz.  RF MEMS: Theory, Design and Technology , 2003 .