Experimental and numerical analysis of a variable area ratio steam ejector

Abstract In the present paper, experimental and CFD results for a 5 kW capacity steam ejector with variable primary nozzle geometry are presented and compared. The variable geometry was achieved by applying a movable spindle at the primary nozzle inlet. Operating conditions were considered in a range that would be suitable for an air-conditioning application, with thermal energy supplied by vacuum tube solar collectors. The CFD model was based on the axi-symmetric representation of the experimental ejector, using water as working fluid. The experimental entrainment ratio varied in the range of 0.1–0.5 depending on operating conditions and spindle tip position. It was found that the primary flow rate can be successfully adjusted by the spindle. CFD and experimental primary flow rates agreed well, with an average relative error of 7.7%. CFD predicted the secondary flow rate and entrainment ratio with good accuracy only in 70% of the cases.

[1]  K. Cizungu,et al.  Performance comparison of vapour jet refrigeration system with environment friendly working fluids , 2001 .

[2]  Latra Boumaraf,et al.  Modeling of an ejector refrigerating system operating in dimensioning and off-dimensioning conditions with the working fluids R142b and R600a , 2009 .

[3]  F. White.  Viscous Fluid Flow , 1974 .

[4]  Andrew Ooi,et al.  CFD analysis of ejector in a combined ejector cooling system , 2005 .

[5]  Yann Bartosiewicz,et al.  Numerical assessment of ejector operation for refrigeration applications based on CFD , 2006 .

[6]  Per Lundqvist,et al.  A year-round dynamic simulation of a solar-driven ejector refrigeration system with iso-butane as a refrigerant , 2007 .

[7]  Bogdan Diaconu,et al.  Analysis of a solar-assisted ejector cooling system for air conditioning , 2009 .

[8]  Mohamed Ouzzane,et al.  The effect of operating conditions on the performance of a supersonic ejector for refrigeration , 2004 .

[9]  Philippe Desevaux,et al.  A method for visualizing the mixing zone between two co-axial flows in an ejector , 2001 .

[10]  Ian W. Eames,et al.  Results of an experimental study of an advanced jet-pump refrigerator operating with R245fa , 2007 .

[11]  Bin-Juine Huang,et al.  Empirical correlation for ejector design , 1999 .

[12]  Yuan-Jen Chang,et al.  Enhancement of a steam-jet refrigerator using a novel application of the petal nozzle , 2000 .

[13]  Ruzhu Wang,et al.  Progress of mathematical modeling on ejectors , 2009 .

[14]  Da-Wen Sun,et al.  Comparative study of the performance of an ejector refrigeration cycle operating with various refrigerants , 1999 .

[15]  Jean-Marie Seynhaeve,et al.  CFD analysis of a supersonic air ejector. Part II: Relation between global operation and local flow features , 2009 .

[16]  Bin-Juine Huang,et al.  A 1-D analysis of ejector performance , 1999 .

[17]  Ian W. Eames,et al.  A new prescription for the design of supersonic jet-pumps: the constant rate of momentum change method , 2002 .

[18]  Weeratunge Malalasekera,et al.  An introduction to computational fluid dynamics - the finite volume method , 2007 .

[19]  Jorge I. Hernández,et al.  The behaviour of a hybrid compressor and ejector refrigeration system with refrigerants 134a and 142b , 2004 .

[20]  Bin-Juine Huang,et al.  Ejector Performance Characteristics and Design Analysis of Jet Refrigeration System , 1985 .

[21]  Changyun Wen,et al.  Numerical investigation of geometry parameters for design of high performance ejectors , 2009 .

[22]  Satha Aphornratana,et al.  A small capacity steam-ejector refrigerator: experimental investigation of a system using ejector with movable primary nozzle , 1997 .

[23]  Saffa Riffat,et al.  Design, testing and mathematical modelling of a small-scale CHP and cooling system (small CHP-ejector trigeneration) , 2007 .

[24]  Jean-Marie Seynhaeve,et al.  CFD analysis of a supersonic air ejector. Part I: Experimental validation of single-phase and two-phase operation , 2009 .

[25]  Bogdan Diaconu,et al.  Numerical assessment of steam ejector efficiencies using CFD , 2009 .

[26]  R. Yapıcı,et al.  Experimental determination of the optimum performance of ejector refrigeration system depending on ejector area ratio , 2008 .

[27]  Satha Aphornratana,et al.  An experimental investigation of a steam ejector refrigerator: the analysis of the pressure profile along the ejector , 2004 .

[28]  T. Sriveerakul,et al.  Performance prediction of steam ejector using computational fluid dynamics: Part 1. Validation of the CFD results , 2007 .

[29]  Masud Behnia,et al.  Investigation and improvement of ejector refrigeration system using computational fluid dynamics technique , 2007 .

[30]  Bogdan Diaconu,et al.  Influence of geometrical factors on steam ejector performance – A numerical assessment , 2009 .

[31]  Satha Aphornratana,et al.  Ejectors: applications in refrigeration technology , 2004 .

[32]  A. Mani,et al.  Experimental investigations on ejector refrigeration system with ammonia , 2007 .

[33]  Wojciech Sobieski.  PERFORMANCE OF AN AIR-AIR EJECTOR: AN ATTEMPT AT NUMERICAL MODELLING , 2003 .