Grain Orientation Evolution and Deformation Behaviors in Pb-Free Solder Interconnects Under Mechanical Stresses

In this study, the effect of mechanical stresses on the recrystallization behavior of Sn-3.0Ag-0.5Cu Pb-free solder interconnects was studied by four-point cyclic bending, shear tests, and tensile tests. Scanning electronic microscopy with electron backscattered diffraction was used to characterize the microstructure and crystallographic orientation of the solder interconnects. The results show that recrystallization occurs under the different mechanical stresses in these tests at room temperature, and that recrystallized grains evolve from subgrains by rotation. Microhardness measurements after shear tests show that the hardness of the recrystallized microstructure was decreased by 15% and 41%, respectively, compared with that of the nonrecrystallized and as-solidified microstructures. Furthermore, the fine-grained microstructure produced after recrystallization facilitated grain boundary sliding. Therefore, the deformation and cracking behaviors were localized in the degraded recrystallized microstructures once recrystallization occurred, accelerating failure of the solder interconnects.

[1]  W. B. Pearson,et al.  A handbook of lattice spacings and structures of metals and alloys , 1958 .

[2]  Thomas R. Bieler,et al.  Crack Development in a Low-Stress PBGA Package due to Continuous Recrystallization Leading to Formation of Orientations with [001] Parallel to the Interface , 2010 .

[3]  T. Mattila,et al.  The Role of Recrystallization in the Failure of SnAgCu Solder Interconnections Under Thermomechanical Loading , 2010, IEEE Transactions on Components and Packaging Technologies.

[4]  Klaus-Jurgen Wolter,et al.  Localized recrystallization and cracking of lead-free solder interconnections under thermal cycling , 2011 .

[5]  Sung K. Kang,et al.  Ag_3Sn plate formation in the solidification of near ternary eutectic Sn–Ag–Cu alloys , 2002 .

[6]  Da-Yuan Shih,et al.  Ag3Sn plate formation in the solidification of near-ternary eutectic Sn-Ag-Cu , 2003 .

[7]  Farhang Pourboghrat,et al.  Incremental recrystallization/grain growth driven by elastic strain energy release in a thermomechanically fatigued lead-free solder joint , 2007 .

[8]  M. E. Kassner,et al.  Current issues in recrystallization: a review , 1997 .

[9]  D. R. Frear,et al.  Morphology of interfacial reaction between lead-free solders and electroless Ni–P under bump metallization , 2000 .

[10]  S. Terashima,et al.  Thermal Fatigue Properties of Sn-1.2Ag-0.5Cu-xNi Flip Chip Interconnects , 2004 .

[11]  Masako Nozaki,et al.  Recrystallization of Sn Grains due to Thermal Strain in Sn-1.2Ag-0.5Cu-0.05Ni Solder , 2004 .

[12]  Tomi Laurila,et al.  Interfacial reactions between lead-free solders and common base materials , 2005 .

[13]  Zhong Chen,et al.  Solid state interfacial reaction of Sn–37Pb and Sn–3.5Ag solders with Ni–P under bump metallization , 2004 .

[14]  K. Tu,et al.  Six cases of reliability study of Pb-free solder joints in electronic packaging technology , 2002 .

[15]  Cheng Yan,et al.  Effects of Solder Volume on Formation and Redeposition of Au-Containing Intermetallics in Ni/Au-SnAgCu-Ni(P) Solder Joints , 2007 .

[16]  D. Frear,et al.  Pb-free solders for flip-chip interconnects , 2001 .

[17]  Seungbae Park,et al.  Three-Dimensional Finite Element Analysis of Multiple-Grained Lead-Free Solder Interconnects , 2008 .

[18]  M. Geers,et al.  Thermomechanical fatigue damage evolution in SAC solder joints , 2007 .

[19]  Sung K. Kang,et al.  The microstructure of Sn in near-eutectic Sn–Ag–Cu alloy solder joints and its role in thermomechanical fatigue , 2004 .

[20]  T. Mattila,et al.  Impact of printed wiring board coatings on the reliability of lead-free chip-scale package interconnections , 2004 .

[21]  Janne J. Sundelin,et al.  Recrystallization behaviour of SnAgCu solder joints , 2008 .

[22]  M. Tanaka,et al.  Improvement of Thermal Fatigue Properties of Sn-Ag-Cu Lead-Free Solder Interconnects on Casio’s Wafer-Level Packages Based on Morphology and Grain Boundary Character , 2009 .

[23]  Thomas R. Bieler,et al.  Cyclic twin nucleation in tin-based solder alloys , 2010 .

[24]  K. S. Kim,et al.  Effects of cooling speed on microstructure and tensile properties of Sn–Ag–Cu alloys , 2002 .

[25]  T. Bieler,et al.  Sn-Ag-Cu Solder Joint Microstructure and Orientation Evolution as a Function of Position and Thermal Cycles in Ball Grid Arrays Using Orientation Imaging Microscopy , 2010 .

[26]  K. N. Subramanian,et al.  Grain-boundary character and grain growth in bulk tin and bulk lead-free solder alloys , 2004 .

[27]  Won Kyoung Choi,et al.  Effects of mechanical deformation and annealing on the microstructure and hardness of Pb-free solders , 2003 .

[28]  Willem D. van Driel,et al.  Facing the challenge of designing for Cu/low-k reliability , 2006, Microelectronics and reliability.

[29]  I. Dutta.  A constitutive model for creep of lead-free solders undergoing strain-enhanced microstructural coarsening: A first report , 2003 .