On enhancing the mechanical behavior of ultra-high performance concrete through multi-scale fiber reinforcement

Abstract Steel fibers are typically used in ultra-high performance concretes (UHPC) to impart flexural ductility and increase fracture toughness. However, the mechanical properties of the steel fibers are underutilized in UHPC, as evidenced by the fact that most of the steel fibers pull out of a UHPC matrix largely undamaged during tensile or flexural tests. This research aims to improve the bond between steel fibers and a UHPC matrix by using steel wool. The underlying mechanism for fiber-matrix bond improvement is the reinforcement of the matrix tunnel, surrounding the steel fibers, by steel wool. Single fiber pullout tests were performed to quantify the effect of steel wool content in UHPC on the fiber-matrix bond. Microscopic observations of pulled-out fibers were used to investigate the fiber-matrix interface. Compared to the control UHPC mixture with no steel wool, significant improvement in the flexural behavior was observed in the UHPC mixtures with steel wool. Thus, the addition of steel wool in steel fiber-reinforced UHPC provides multi-scale reinforcement that leads to significant improvement in fiber-matrix bond and mechanical properties of UHPC.

[1]  Victor C. Li,et al.  Composite Properties of High-Strength, High-Ductility Concrete , 2013 .

[2]  Kamal H. Khayat,et al.  Mechanical Properties of Ultra-High-Performance Concrete Enhanced with Graphite Nanoplatelets and Carbon Nanofibers , 2016 .

[3]  Nemkumar Banthia,et al.  Fracture toughness of micro-fiber reinforced cement composites , 1996 .

[4]  Y. Yoon,et al.  Effect of fiber content on mechanical and fracture properties of ultra high performance fiber reinforced cementitious composites , 2013 .

[5]  M. Lachemi,et al.  High-early-strength ductile cementitious composites with characteristics of low early-age shrinkage for repair of infrastructures , 2015 .

[6]  F. Maou,et al.  Durability of a multiscale fibre reinforced cement composite in aggressive environment under service load , 2007 .

[7]  Jiangtao Yu,et al.  A strain-hardening cementitious composites with the tensile capacity up to 8% , 2017 .

[8]  Hjh Jos Brouwers,et al.  Development of Ultra-High Performance Fibre Reinforced Concrete (UHPFRC): Towards an efficient utilization of binders and fibres , 2015 .

[9]  Günther Meschke,et al.  Experimental, analytical and numerical analysis of the pullout behaviour of steel fibres considering different fibre types, inclinations and concrete strengths , 2014 .

[10]  Wille Kay,et al.  高強度真鍮メッキ直鋼繊維の引抜性状に対する超高性能コンクリートの影響 | 文献情報 | J-GLOBAL 科学技術総合リンクセンター , 2013 .

[11]  M. Şahmaran,et al.  Deflection-hardening hybrid fiber reinforced concrete: The effect of aggregate content , 2016 .

[12]  G. Yıldırım.  Dimensional stability of deflection‐hardening hybrid fiber reinforced concretes with coarse aggregate: Suppressing restrained shrinkage cracking , 2018, Structural Concrete.

[13]  Surendra P. Shah,et al.  Correlation of fiber dispersion, rheology and mechanical performance of FRCs , 2007 .

[14]  Martin van de Ven,et al.  Electrical conductivity of asphalt mortar containing conductive fibers and fillers , 2009 .

[15]  Antoine E. Naaman,et al.  Properties of strain hardening ultra high performance fiber reinforced concrete (UHP-FRC) under direct tensile loading , 2014 .

[16]  Antoine E. Naaman,et al.  Strain-hardening UHP-FRC with low fiber contents , 2011 .

[17]  Antoine E. Naaman,et al.  Effect of mechanical clamping on the pull-out response of hooked steel fibers embedded in cementitious matrices , 2022 .

[18]  P. Rossi,et al.  High Performance Multimodal Fiber Reinforced Cement Composites (HPMFRCC) , 1997 .

[19]  Taher Abu-Lebdeh,et al.  Effect of matrix strength on pullout behavior of steel fiber reinforced very-high strength concrete composites , 2011 .

[20]  Benjamin A. Graybeal,et al.  Ultra-High Performance Concrete: A State-of-the-Art Report for the Bridge Community , 2013 .

[21]  Sidney Mindess,et al.  Fibre Reinforced Cementitious Composites , 1990 .

[22]  A. Naaman,et al.  Pullout Behavior of High-Strength Steel Fibers Embedded in Ultra-High-Performance Concrete , 2012 .

[23]  Antoine E. Naaman,et al.  Bond-Slip Mechanisms of Steel Fibers in Concrete , 1991 .

[24]  Davide Zampini,et al.  Microfiber and Macrofiber Hybrid Fiber-Reinforced Concrete , 2005 .

[25]  Young Soo Yoon,et al.  Structural performance of ultra-high-performance concrete beams with different steel fibers , 2015 .

[26]  Changbin Joh,et al.  Structural behavior of ultra high performance concrete beams subjected to bending , 2010 .

[27]  Sofiane Amziane,et al.  Flowability of fibre-reinforced concrete and its effect on the mechanical properties of the material , 2010 .

[28]  Antoine E. Naaman,et al.  Strain rate dependent properties of ultra high performance fiber reinforced concrete (UHP-FRC) under tension , 2015 .

[29]  Hwai Chung Wu,et al.  Matrix design for pseudo-strain-hardening fibre reinforced cementitious composites , 1995 .

[30]  Senot Sangadji,et al.  Addressing Infrastructure Durability and Sustainability by Self Healing Mechanisms - Recent Advances in Self Healing Concrete and Asphalt , 2013 .

[31]  Alberto Meda,et al.  Bending and Uniaxial Tensile Tests on Concrete Reinforced with Hybrid Steel Fibers , 2005 .

[32]  Antoine E. Naaman,et al.  Effect of Ultra-High-Performance Concrete on Pullout Behavior of High-Strength Brass-Coated Straight Steel Fibers , 2013 .

[33]  E. Parant,et al.  Mécanismes d'endommagement et comportements mécaniques d'un composite cimentaire fibré multi-échelles sous sollicitations sévères : fatigue, choc, corrosion , 2004 .

[34]  P. Rossi,et al.  Tensile and bending behaviour of a strain hardening cement-based composite: Experimental and numerical analysis , 2012 .

[35]  Manfred N. Partl,et al.  Uniformity and mechanical properties of dense asphalt concrete with steel wool fibers , 2013 .

[36]  Ravi Ranade.  Advanced cementitious composite development for resilient and sustainable infrastructure , 2014 .

[37]  K. Khayat,et al.  Effect of nano-SiO2 particles and curing time on development of fiber-matrix bond properties and microstructure of ultra-high strength concrete , 2017 .

[38]  Manfred N. Partl,et al.  Induction healing of dense asphalt concrete , 2013 .

[39]  Antoine E. Naaman,et al.  Ultra-high performance concrete and fiber reinforced concrete: achieving strength and ductility without heat curing , 2012 .

[40]  J. Mier,et al.  Single fiber pullout from hybrid fiber reinforced concrete , 2001 .

[41]  M. Şahmaran,et al.  Impact behaviour of nanomodified deflection-hardening fibre-reinforced concretes , 2020 .

[43]  A. Ashour,et al.  Impact resistance of deflection‐hardening fiber reinforced concretes with different mixture parameters , 2019, Structural Concrete.

[44]  Antoine E. Naaman,et al.  Engineered Steel Fibers with Optimal Properties for Reinforcement of Cement Composites , 2003 .

[45]  James L O'Daniel,et al.  Impact of Steel Fiber Size and Shape on the Mechanical Properties of Ultra-High Performance Concrete , 2015 .