Investigating the thermomechanical properties and intermetallic layer formation of Bi micro-alloyed low-Ag content solders

Abstract In our research, we performed comparative analyses concerning various lead-free SAC (Sn96.5Ag3Cu0.5, Sn95.5Ag4Cu0.5) and two types of micro-alloyed SAC (SnAgCu + Bi + Sb) solder alloys. The mechanical properties of these solder alloys were characterised by measuring the shear strength of 0603 (1.5 × 0.75 mm) size chip resistors’ joints. We designed a testboard, which contains fifty pieces of 0603 size resistors for mechanical characterisation and for measuring the thickness of intermetallic layers. During the experiment, twenty-eight pieces of testboards were soldered with vapour phase soldering (seven with each solder alloy) and sixteen of them were subjected to Thermal-Shock (TS) life-time tests with temperature range of +140 to −40 °C up to 2000 cycles. The intermetallic layer (IML) formation was investigated with Scanning Electron Microscopy (SEM) and Scanning Transmission Electron Microscopy (STEM) methods; and the growth of the layer was analysed by measuring the IML thickness on cross-sectional samples after given TS cycles. It is shown that the thickness of the intermetallic layer in as-reflowed samples (samples without aging) depends on the silver content of the given alloy. Besides, the layer growth rate during Thermal Shock tests is affected by the number of intermetallic layer grain-boundaries along a unit of length.

[1]  Y. C. Chan,et al.  Study of micro-BGA solder joint reliability , 2001, Microelectron. Reliab..

[2]  M. Amagai.  A study of nanoparticles in Sn-Ag based lead free solders , 2008 .

[3]  Manoj Gupta,et al.  Interfacial intermetallic growth and shear strength of lead-free composite solder joints , 2009 .

[4]  Sung K. Kang,et al.  Ag_3Sn plate formation in the solidification of near ternary eutectic Sn–Ag–Cu alloys , 2002 .

[5]  H. Esaka,et al.  Formation Mechanism of Eutectic Cu6Sn5 and Ag3Sn after Growth of Primary β-Sn in Sn-Ag-Cu Alloy , 2011 .

[6]  Hwa-Teng Lee,et al.  Effect of cooling rate on Ag3Sn formation in Sn-Ag based lead-free solder , 2009, 2009 11th Electronics Packaging Technology Conference.

[7]  Sung K. Kang,et al.  The Microstructure, Thermal Fatigue, and Failure Analysis of Near-Ternary Eutectic Sn-Ag-Cu Solder Joints , 2004 .

[8]  Balázs Illés,et al.  Numerical simulation of condensate layer formation during vapour phase soldering , 2014 .

[9]  M. Amagai,et al.  High drop test reliability: lead-free solders , 2004, 2004 Proceedings. 54th Electronic Components and Technology Conference (IEEE Cat. No.04CH37546).

[10]  Mingyu Li,et al.  Interfacial reactions of eutectic Sn3.5Ag and pure tin solders with Cu substrates during liquid-state soldering , 2012 .

[11]  Jin Yu,et al.  Controlling Ag3Sn plate formation in near-ternary-eutectic Sn-Ag-Cu solder by minor Zn alloying , 2004 .

[12]  R. Pandher,et al.  Drop Shock Reliability of Lead-Free Alloys - Effect of Micro-Additives , 2007, 2007 Proceedings 57th Electronic Components and Technology Conference.

[13]  C. Y. Liu,et al.  Evolution of Ag3Sn compound formation in Ni/Sn5Ag/Cu solder joint , 2008 .

[14]  P. Svasta,et al.  VPS solution for lead-free soldering in EMS industries , 2008, 2008 2nd Electronics System-Integration Technology Conference.

[15]  Eduardo Monlevade,et al.  Failure Mechanisms and Crack Propagation Paths in Thermally Aged Pb-Free Solder Interconnects , 2007 .

[16]  M. Dusek,et al.  The impact of thermal cycling regime on the shear strength of lead‐free solder joints , 2005 .

[17]  Balázs Illés,et al.  Modeling method of heat transfer during Vapour Phase Soldering based on filmwise condensation theory , 2013 .

[18]  A. Haseeb,et al.  Understanding the effects of addition of copper nanoparticles to Sn‐3.5 Ag solder , 2011 .

[19]  Jun Shen,et al.  Microstructural evolutions of the Ag nano-particle reinforced SnBiCu-xAg/Cu solder joints during liquid aging , 2012, Journal of Materials Science: Materials in Electronics.

[20]  Jun Shen,et al.  Abnormal growth of Ag3Sn intermetallic compounds in Sn-Ag lead-free solder , 2006 .

[21]  K. Tu,et al.  Tin–lead (SnPb) solder reaction in flip chip technology , 2001 .

[22]  A. Pietrikova,et al.  VPS and reliability of solder joint , 2009, 2009 15th International Symposium for Design and Technology of Electronics Packages (SIITME).

[23]  L. Tsao.  Evolution of nano-Ag3Sn particle formation on Cu–Sn intermetallic compounds of Sn3.5Ag0.5Cu composite solder/Cu during soldering , 2011 .

[24]  O. Krammer,et al.  Comparing the intermetallic layer formation of Infrared and Vapour Phase soldering , 2011, Proceedings of the 2011 34th International Spring Seminar on Electronics Technology (ISSE).

[25]  S. Gale,et al.  Investigation of the Role of Void Formation at the Cu-to-Intermetallic Interface on Aged Drop Test Performance , 2007, IEEE Transactions on Electronics Packaging Manufacturing.

[26]  R. A. Fournelle,et al.  Theory for intermetallic phase growth between cu and liquid Sn-Pb solder based on grain boundary diffusion control , 1998 .