Numerical investigation of heat transfer in a CO2 two-phase ejector

Abstract In this paper, the influence of heat transfer in the walls of an R744 two-phase ejector on ejector performance was investigated. A numerical investigation was performed using a computational fluid dynamic (CFD) model of the R744 two-phase flow coupled with the heat transfer inside the ejector. An ejector equipped with thermocouple channels was designed and manufactured to investigate temperature distribution in the inner walls under boundary conditions typical for a refrigeration and air-conditioning application in a supermarket. The ejector was installed on the test rig to perform a test series that evaluated the outer walls of the ejector with and without insulation. The experimental results were used to validate the proposed CFD model, and a numerical investigation was performed to analyse the influence of heat transfer on ejector performance. The motive nozzle and suction nozzle mass flow rates accuracies were within ±7% and ±15%, respectively. In addition, the proposed CFD model predicted the wall temperatures with ±5 K accuracy for most of the validated points. The heat transfer coefficient of the R744 two-phase flow inside the ejector is presented. The non-adiabatic inner walls degraded ejector performance. The maximum reduction of the mass entrainment ratio reached approximately 13%.

[1]  Trond Andresen,et al.  Experimental and numerical investigation of the influence of the two-phase ejector geometry on the performance of the R744 heat pump , 2012 .

[2]  Brian A. Fricke,et al.  Comparative analysis of various CO2 configurations in supermarket refrigeration systems , 2014 .

[3]  Miad Yazdani,et al.  Numerical modeling of two-phase supersonic ejectors for work-recovery applications , 2012 .

[4]  N. Agrawal,et al.  Performance evaluation of a non-adiabatic capillary tube in a transcritical CO2 heat pump cycle , 2008 .

[5]  Armin Hafner,et al.  Modified homogeneous relaxation model for the r744 trans-critical flow in a two-phase ejector , 2018 .

[6]  J. Kestin,et al.  Physical aspects of the relaxation model in two-phase flow , 1990, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.

[7]  Armin Hafner,et al.  1D Computational model of a two-phase R744 ejector for expansion work recovery. , 2011 .

[8]  Armin Hafner,et al.  Full-scale multi-ejector module for a carbon dioxide supermarket refrigeration system: Numerical study of performance evaluation , 2017 .

[9]  Adriano Milazzo,et al.  CFD Modeling of the Supersonic Condensation Inside a Steam Ejector , 2016 .

[10]  Sébastien Poncet,et al.  Turbulence modeling of a single-phase R134a supersonic ejector. Part 1: Numerical benchmark , 2016 .

[11]  P. Roache.  Perspective: A Method for Uniform Reporting of Grid Refinement Studies , 1994 .

[12]  Sven Försterling,et al.  Multi-ejector concept for R-744 supermarket refrigeration , 2014 .

[13]  Armin Hafner,et al.  Development and performance mapping of a multi-ejector expansion work recovery pack for R744 vapour compression units. , 2015 .

[14]  Juergen Koehler,et al.  Numerical investigation of a two-phase CO2 ejector , 2014 .

[15]  Jean-Marie Seynhaeve,et al.  1-D Modeling of Supersonic CarbonDioxide Two-Phase FLow through Ejector Motive Nozzle , 2010 .

[16]  Adriano Milazzo,et al.  Future perspectives in ejector refrigeration , 2017 .

[17]  Fabio Inzoli,et al.  Computational fluid-dynamics modeling of supersonic ejectors: Screening of turbulence modeling approaches , 2017 .

[18]  Yann Bartosiewicz,et al.  Computational and Experimental Analysis of Supersonic Air Ejector: Tubrulence Modeling and Assessemnt of 3D Effects , 2015 .

[19]  Fabio Inzoli,et al.  Ejector refrigeration: A comprehensive review , 2016 .

[20]  Armin Hafner,et al.  A computational model of a transcritical R744 ejector based on a homogeneous real fluid approach , 2013 .

[22]  Stefan Elbel,et al.  Historical and present developments of ejector refrigeration systems with emphasis on transcritical carbon dioxide air-conditioning applications , 2011 .

[23]  Armin Hafner,et al.  A CFD-based investigation of the energy performance of two-phase R744 ejectors to recover the expansion work in refrigeration systems: An irreversibility analysis , 2014 .

[24]  S. Wongwises,et al.  Numerical investigation of refrigerant flow through non-adiabatic capillary tubes , 2002 .

[25]  Armando C. Oliveira,et al.  On the selection of a turbulence model for the simulation of steam ejectors using CFD , 2017 .

[26]  Vincenzo Dossena,et al.  Computational Fluid Dynamics Modeling of Flashing Flow in Convergent-Divergent Nozzle , 2018 .

[27]  Min-Soo Kim,et al.  Studies on the performance of a CO2 air conditioning system using an ejector as an expansion device , 2014 .

[28]  Armin Hafner,et al.  Novel integrated CO2 vapour compression racks for supermarkets. Thermodynamic analysis of possible system configurations and influence of operational conditions , 2018 .

[29]  Armin Hafner,et al.  Application range of the HEM approach for CO2 expansion inside two-phase ejectors for supermarket refrigeration systems , 2015 .

[30]  Kenneth Bank Madsen,et al.  Performance mapping of the R744 ejectors for refrigeration and air conditioning supermarket application: A hybrid reduced-order model , 2018, Energy.

[31]  Jostein Pettersen,et al.  Fundamental process and system design issues in CO2 vapor compression systems , 2004 .

[32]  Yunting Ge,et al.  State-of-the-art technologies for transcritical R744 refrigeration systems – a theoretical assessment of energy advantages for European food retail industry , 2017 .

[33]  Adriano Milazzo,et al.  Performance analysis of a supersonic ejector cycle working with R245fa , 2015 .

[34]  A. Milazzo,et al.  The surface roughness effect on the performance of supersonic ejectors , 2017 .

[35]  Paolo Chiesa,et al.  An Integrated Lumped Parameter-CFD approach for off-design ejector performance evaluation , 2015 .

[36]  Predrag Stojan Hrnjak,et al.  Experimental validation of a prototype ejector designed to reduce throttling losses encountered in transcritical R744 system operation , 2008 .

[37]  Armin Hafner,et al.  Performance assessment of an off-the-shelf R744 heat pump equipped with an ejector , 2013 .

[38]  Armin Hafner,et al.  Shape optimisation of a two-phase ejector for CO2 refrigeration systems , 2017 .

[39]  Dirk Lucas,et al.  3D CFD simulation of flashing flows in a converging-diverging nozzle , 2015 .

[40]  Christopher J. Freitas,et al.  The issue of numerical uncertainty , 2002 .

[41]  Armin Hafner,et al.  HEM and HRM accuracy comparison for the simulation of CO2 expansion in two-phase ejectors for supermarket refrigeration systems , 2017 .