High-aspect ratio vertical comb-drive actuator with small self-aligned finger gaps

A vertical comb-drive actuator with thin, high-aspect ratio comb fingers and small self-aligned gaps is presented. Key to the actuator design is the self-aligned, offset comb-drive fingers, which are fabricated with small gaps (/spl les/2 /spl mu/m) using a single lithography step. The offset comb fingers are fabricated using two thick conducting layers separated by a thin dielectric layer. The lower fingers are formed from the device layer (20 /spl mu/m) of an silicon-on-insulator (SOI) substrate, while an in situ -doped polysilicon layer (20 /spl mu/m), deposited in an epitaxial reactor (Epipoly), is used for the upper comb fingers. The Epipoly films have been optimized and characterized for application as structural and electrical components. The offset comb fingers are formed using a combination of deep-reactive ion etching (DRIE), thin oxide barrier layer growth, and an isotropic dry silicon etch (XeF/sub 2/) of selected areas of the Epipoly layer. The actuator has been implemented in a high fill-factor (>90%) micromirror array for optical telecommunications applications. Large continuous scan angles (/spl plusmn/10/spl deg/) with actuation voltages <60 V have been measured with no pull-in phenomena observed.

[1]  Gary K. Fedder,et al.  A CMOS-MEMS mirror with curled-hinge comb drives , 2003 .

[2]  S. Ueda,et al.  A rotational comb-driven micromirror with a large deflection angle and low drive voltage , 2002, Technical Digest. MEMS 2002 IEEE International Conference. Fifteenth IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.02CH37266).

[3]  A novel fabrication method of a vertical comb drive using a single SOI wafer for optical MEMS applications , 2003, TRANSDUCERS '03. 12th International Conference on Solid-State Sensors, Actuators and Microsystems. Digest of Technical Papers (Cat. No.03TH8664).

[4]  Ming C. Wu,et al.  A 2D scanner by surface and bulk micromachined vertical comb actuators , 2003, 2003 IEEE/LEOS International Conference on Optical MEMS (Cat. No.03EX682).

[5]  Luke P. Lee,et al.  VERTICAL MICROLENS SCANNER FOR 3D IMAGING , 2002 .

[6]  Kam Y. Lau,et al.  A FLAT HIGH-FREQUENCY SCANNING MICROMIRROR , 2000 .

[7]  G. Fedder,et al.  Laminated high-aspect-ratio microstructures in a conventional CMOS process , 1996, Proceedings of Ninth International Workshop on Micro Electromechanical Systems.

[8]  Herbert H. Woodson,et al.  Electromechanical Dynamics. Part I: Discrete Systems , 1968 .

[9]  N. Tien,et al.  Electrostatic model for an asymmetric combdrive , 2000, Journal of Microelectromechanical Systems.

[10]  Weileun Fang,et al.  The BELST II process for a silicon high-aspect-ratio micromaching vertical comb actuator and its applications , 2004 .

[11]  Kristofer S. J. Pister,et al.  Torsional Micromirrors with Lateral Actuators , 2001 .

[12]  W. Riethmüller,et al.  Deposition of thick doped polysilicon films with low stress in an epitaxial reactor for surface micromachining applications , 1995 .

[13]  Pasqualina M. Sarro,et al.  Bipolar-compatible epitaxial poly for smart sensors: stress minimization and applications , 1997 .

[14]  M.C. Wu,et al.  Low-voltage, large-scan angle MEMS analog micromirror arrays with hidden vertical comb-drive actuators , 2004, Journal of Microelectromechanical Systems.

[15]  K. J. Gabriel,et al.  Design, fabrication, and operation of submicron gap comb-drive microactuators , 1992 .

[16]  Hiroshi Toshiyoshi,et al.  A low voltage, large scan angle MEMS micromirror array with hidden vertical comb-drive actuators for WDM routers , 2002, Optical Fiber Communication Conference and Exhibit.

[17]  R. L. Edwards,et al.  Measurements of Young's modulus, Poisson's ratio, and tensile strength of polysilicon , 1997, Proceedings IEEE The Tenth Annual International Workshop on Micro Electro Mechanical Systems. An Investigation of Micro Structures, Sensors, Actuators, Machines and Robots.

[18]  William C. Tang,et al.  Electrostatic Comb Drive Levitation And Control Method , 1992 .

[19]  T. Kamins.  Polycrystalline silicon for integrated circuit applications , 1988 .

[20]  Single crystal silicon (SCS) micromirror arrays using deep silicon etching and IR alignment , 2000, Proceedings IEEE Thirteenth Annual International Conference on Micro Electro Mechanical Systems (Cat. No.00CH36308).

[21]  S. Wolf,et al.  Silicon Processing for the VLSI Era , 1986 .

[22]  Hongrui Jiang,et al.  Integrated polysilicon and DRIE bulk silicon micromachining for an electrostatic torsional actuator , 1999 .

[23]  K. Pister,et al.  Laterally actuated torsional micromirrors for large static deflection , 2003, IEEE Photonics Technology Letters.

[24]  M. Wu,et al.  A scanning micromirror with angular comb drive actuation , 2002, Technical Digest. MEMS 2002 IEEE International Conference. Fifteenth IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.02CH37266).

[25]  Abraham P. Lee,et al.  Electrostatic comb drive for vertical actuation , 1997, Photonics West - Micro and Nano Fabricated Electromechanical and Optical Components.

[26]  L. Warne,et al.  Electrophysics of micromechanical comb actuators , 1995 .

[27]  V. Milanovic.  Multilevel beam SOI-MEMS fabrication and applications , 2002, 9th International Conference on Electronics, Circuits and Systems.