Guided wave based detection of damage in honeycomb core sandwich structures

We report on the Lamb wave type guided wave propagation in honeycomb core sandwich structures. An experimental study supported by theoretical evaluation of the guided wave characteristics is presented that proves the potential of Lamb wave type guided wave for detection of damage in sandwich structures. A sandwich panel is fabricated with planar dimension of 600 mm x 600 mm, having a core thickness of 7 mm, cell size of 5 mm and 0.1 mm thick aluminum face sheets. Thin piezoelectric patch actuators and sensors are used to excite and sense a frequency band limited guided wave with a central frequency. A linear phased array of piezoelectric patch actuators is used to achieve higher signal strength and directivity. Group velocity dispersion curves and corresponding frequency response of sensed signal are obtained experimentally. Linearity between the excitation signal amplitude and the corresponding sensed signal amplitude is found for certain range of parameters. The nature of damping present in the sandwich panel is monitored by measuring the sensor signal amplitude at various different distances measured from the center of the linear phased array. Indentation and low velocity impact induced damages of increasing diameter covering several honeycomb cells are created. Crushing of honeycomb core with rupture of face sheet is observed while introducing the damage. The damages are then detected experimentally by pitch-catch interrogation with guided waves and wavelet transform of the sensed signal. Signal amplitudes are analyzed for various different sizes of damages to differentiate the damage size/severity. Monotonic changes in the sensor signal amplitude due to increase in the damage size has been established successfully. With this approach it is possible to locate and monitor the damages with the help of phased array and by tracking the wave packets scattered from the damages. (C) 2012 Elsevier Ltd. All rights reserved.

[1]  M. Lemistre,et al.  Damage localization in composite plates using wavelet transform processing on Lamb wave signals , 1999 .

[2]  Constantinos Soutis,et al.  Detection of Low-velocity Impact Damage in Composite Plates using Lamb Waves , 2004 .

[3]  Constantinos Soutis,et al.  Damage detection in composite materials using lamb wave methods , 2002 .

[4]  Guoliang Huang,et al.  Guided wave propagation in honeycomb sandwich structures using a piezoelectric actuator/sensor system , 2009 .

[5]  Emmanuel Moulin,et al.  Radome health monitoring with Lamb waves: experimental approach , 2000 .

[6]  Constantinos Soutis,et al.  Non-destructive inspection of sandwich and repaired composite laminated structures , 2005 .

[7]  Srinivasan Gopalakrishnan,et al.  Rapid localization of damage using a circular sensor array and Lamb wave based triangulation , 2010 .

[8]  Constantinos Soutis,et al.  Structural health monitoring techniques for aircraft composite structures , 2010 .

[9]  Constantinos Soutis,et al.  Piezoelectric transducer arrangement for the inspection of large composite structures , 2007 .

[10]  Joseph L. Rose,et al.  Rapid Inspection of Composite Skin-Honeycomb Core Structures with Ultrasonic Guided Waves , 2003 .

[11]  Constantinos Soutis,et al.  Lamb waves for the non-destructive inspection of monolithic and sandwich composite beams , 2005 .

[12]  D. Roy Mahapatra,et al.  A spectral finite element model for analysis of axial–flexural–shear coupled wave propagation in laminated composite beams , 2003 .

[13]  David Devillers,et al.  Health monitoring of sandwich plates based on the analysis of the interaction of Lamb waves with damages , 2001, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[14]  D. Roy Mahapatra,et al.  Numerical analysis of Lamb wave generation in piezoelectric composite IDT , 2005, IEEE Transactions on Ultrasonics, Ferroelectrics and Frequency Control.

[15]  H. Lamb.  On waves in an elastic plate , 1917 .

[16]  L. Ye,et al.  A damage identification technique for CF/EP composite laminates using distributed piezoelectric transducers , 2002 .