Design and Optimization of a Natural Graphite/Iron Phosphate Lithium-Ion Cell

This paper uses a model for a natural graphite/lithium hexafluoro phosphate (ethylene carbonate:diethyl carbonate)/iron phosphate lithium-ion cell in order to study its performance and aid in its optimization. The model is used to generate Ragone plots for various designs, where both the average power of the cell and the peak power, defined at 80% depth-of-discharge for a 30 s pulse, are evaluated. This allows us to assess the ability of this chemistry to achieve the U.S. Department of Energy goals. The model is then used to maximize the specific energy of the cell by optimizing the design for a fixed time of discharge. The cell was optimized for the porosity and thickness of the positive electrode, while holding constant the capacity ratio of the two electrodes, the thickness and porosity of the separator, the electrolyte concentration, and the porosity of the negative electrode. The effect of the capacity ratio was qualitatively examined. The optimization was performed for discharge times ranging from 10 h to 2 min in order to map the maximum performance of this chemistry under a wide operating range. The study allows us to gauge the ability of this chemistry to be used in a particular application. The optimized designs derived in this paper are expected to be a starting point for battery manufacturers and to help decrease the time to commercialization. © 2004 The Electrochemical Society. All rights reserved.

[1]  J. Tarascon,et al.  Comparison of Modeling Predictions with Experimental Data from Plastic Lithium Ion Cells , 1996 .

[2]  A. Varma,et al.  Chemical Reaction and Reactor Engineering , 1986 .

[3]  Marc Doyle,et al.  Computer Simulations of a Lithium-Ion Polymer Battery and Implications for Higher Capacity Next-Generation Battery Designs , 2003 .

[4]  M. Doyle,et al.  Modeling of Galvanostatic Charge and Discharge of the Lithium/Polymer/Insertion Cell , 1993 .

[5]  John Newman,et al.  Variable Diffusivity in Intercalation Materials A Theoretical Approach , 1996 .

[6]  John Newman,et al.  Predictions of Specific Energies and Specific Powers of Double‐Layer Capacitors Using a Simplified Model , 2000 .

[7]  Karen E. Thomas,et al.  Comparison of lithium-polymer cell performance with unity and nonunity transference numbers , 1999 .

[8]  M. Doyle,et al.  Simulation and Optimization of the Dual Lithium Ion Insertion Cell , 1994 .

[9]  Marc Doyle,et al.  Mathematical Modeling of the Lithium Deposition Overcharge Reaction in Lithium‐Ion Batteries Using Carbon‐Based Negative Electrodes , 1999 .

[10]  Ralph E. White,et al.  Comparison between Computer Simulations and Experimental Data for High-Rate Discharges of Plastic Lithium-Ion Batteries , 2000 .

[11]  Ann Marie Sastry,et al.  Conduction in Multiphase Particulate'Fibrous Networks Simulations and Experiments on Li-ion Anodes , 2003 .

[12]  John Newman,et al.  Optimization of Porosity and Thickness of a Battery Electrode by Means of a Reaction‐Zone Model , 1995 .

[13]  Yet-Ming Chiang,et al.  Electronically conductive phospho-olivines as lithium storage electrodes , 2002, Nature materials.

[14]  Joongpyo Shim,et al.  Effect of electrode density on cycle performance and irreversible capacity loss for natural graphite anode in lithium-ion batteries , 2003 .

[15]  M. Verbrugge,et al.  Electrochemical analysis of lithiated graphite anodes , 2003 .

[16]  John Newman,et al.  Maximum Effective Capacity in An Ohmically Limited Porous-Electrode , 1975 .

[17]  Venkat Srinivasan,et al.  Discharge Model for the Lithium Iron-Phosphate Electrode , 2004 .

[18]  Walter van Schalkwijk,et al.  Advances in Lithium Ion Batteries Introduction , 2002 .

[19]  Michikazu Hara,et al.  Structural and Kinetic Characterization of Lithium Intercalation into Carbon Anodes for Secondary Lithium Batteries , 1995 .

[20]  Joongpyo Shim,et al.  Cycling performance of low-cost lithium ion batteries with natural graphite and LiFePO4 , 2003 .