Optimal parameter settings for rough and finish machining of die steels in powder-mixed EDM

The present study was undertaken to identify the appropriate parameter settings for rough and finish machined surface for EN31, H11, and high carbon high chromium (HCHCr) die steel materials in a powder-mixed electric discharge machining process. The effect of seven different process variables along with some of their interactions was evaluated using a dummy-treated experimental design and analysis of variance. Material removal rate (MRR), tool wear rate, and surface finish were measured after each trial and analyzed. The parameter settings for rough and finished machining operations were obtained. EN31 exhibited maximum MRR as compared to the other two materials at similar process settings. Copper (Cu) electrode with aluminum suspended in the dielectric maximized the MRR. Suspending powder in the dielectric resulted in surface modification. Graphite powder showed a lower MRR but improved the surface finish. HCHCr require higher current and pulse on settings for initiating a machining cut and works best in combination with tungsten–Cu electrode and graphite powder for improved finish. The MRR for H11 is lower than EN31 but significantly higher than HCHCr under same process conditions.

[1]  B. Yan,et al.  Improvement of surface finish on SKD steel using electro-discharge machining with aluminum and surfactant added dielectric , 2005 .

[2]  Rupinder Singh,et al.  Surface modification by electrical discharge machining: A review , 2009 .

[3]  Yih-fong Tzeng,et al.  Effects of Powder Characteristics on Electrodischarge Machining Efficiency , 2001 .

[4]  Pradeep Kumar,et al.  PARAMETRIC OPTIMIZATION OF POWDER MIXED ELECTRICAL DISCHARGE MACHINING BY RESPONSE SURFACE METHODOLOGY , 2005 .

[5]  Anirban Bhattacharya,et al.  Optimization of powder mixed electric discharge machining using dummy treated experimental design with analytic hierarchy process , 2012 .

[6]  Kuang-Yuan Kung,et al.  Material removal rate and electrode wear ratio study on the powder mixed electrical discharge machining of cobalt-bonded tungsten carbide , 2009 .

[7]  Norliana Mohd Abbas,et al.  A review on current research trends in electrical discharge machining (EDM) , 2007 .

[8]  W. Zhao,et al.  The application of research on powder mixed EDM in rough machining , 2002 .

[9]  L. Dabrowski,et al.  Study of electrical discharge machining using powder-suspended working media , 2003 .

[10]  Elsa Henriques,et al.  Electrical discharge machining using simple and powder-mixed dielectric: The effect of the electrode area in the surface roughness and topography , 2008 .

[11]  Pradeep Kumar,et al.  Effect of Silicon Powder Mixed EDM on Machining Rate of AISI D2 Die Steel , 2007 .

[12]  P. Saha,et al.  Taguchi analysis of surface modification technique using W-Cu powder metallurgy sintered tools in EDM and characterization of the deposited layer , 2011 .

[13]  Anirban Bhattacharya,et al.  Study of Material Transfer Mechanism in Die Steels Using Powder Mixed Electric Discharge Machining , 2012 .

[14]  Y.-C. Lin,et al.  Optimization of electrodischarge machining parameters on ZrO2 ceramic using the Taguchi method , 2010 .

[15]  Elsa Henriques,et al.  Effect of the powder concentration and dielectric flow in the surface morphology in electrical discharge machining with powder-mixed dielectric (PMD-EDM) , 2008 .

[16]  Yusuf Keskin,et al.  An experimental study for determination of the effects of machining parameters on surface roughness in electrical discharge machining (EDM) , 2006 .

[17]  M. L. Jeswani,et al.  Effect of the addition of graphite powder to kerosene used as the dielectric fluid in electrical discharge machining , 1981 .

[18]  K. Furutani,et al.  Influence of electrical conditions on performance of electrical discharge machining with powder suspended in working oil for titanium carbide deposition process , 2009 .

[19]  E. Henriques,et al.  Influence of silicon powder-mixed dielectric on conventional electrical discharge machining , 2003 .

[20]  Naotake Mohri,et al.  A new process of finish machining on free surface by EDM methods , 1991 .

[21]  Quan Ming,et al.  Powder-suspension dielectric fluid for EDM , 1995 .

[22]  P. Saha,et al.  Artificial neural network model in surface modification by EDM using tungsten–copper powder metallurgy sintered electrodes , 2010 .