Probabilistic process simulation to predict process induced distortions of a composite frame

Within this work, an enhanced simulation strategy for predicting process-induced distortions and residual stresses of composite structures is developed, while taking into account probabilistic variations. The simulation strategy is demonstrated for a carbon fibre-reinforced frame of an aircraft fuselage. Based on a sequentially coupled temperature-displacement analysis, temperature and degree of cure distributions as well as stresses, strains, and distortions are determined. For the description of the reaction kinetic, a phenomenological-based model considering chemical and diffusion-controlled reactions is introduced. The mechanical material behavior is described by a viscoelastic material model depending on temperature, time, and degree of cure. Corresponding process-induced distortions and occurring residual stresses are calculated and analyzed. The results of the process-induced distortions are used to derive a compensated tooling design. To analyze the effect of statistical and systematic deviations of underlying process and material parameters, a procedure for a probabilistic process simulation is created. Based on a first sensitivity analysis, a design of experiment is performed over a specified parameter range. From this surrogate, models are derived to enable a full but efficient probabilistic analysis of spring-in angles and residual stresses at multiple frame positions. The effect of process parameter variations and fluctuation of inherent material properties on process-induced distortions is assessed. Moreover, the influence of different process cycles is shown. This allows to determine the expected range of the final part distortion and to derive the resulting tolerances during assembly. For validation of the probabilistic process simulation, several frames are manufactured at different process conditions, and frame geometries are measured by digital image correlation technique. The resulting part thicknesses, spring-in angles, and global frame distortions are determined. Finally, a comparison of measurements and probabilistic predictions is given, and results are evaluated with respect to main sensitivities.

[1]  Donald W. Radford,et al.  Shape Instabilities in Composites Resulting from Laminate Anisotropy , 1993 .

[2]  Dilek Kumlutaş,et al.  A numerical study on the coefficients of thermal expansion of fiber reinforced composite materials , 2007 .

[3]  Maciej Kumosa,et al.  An evaluation of the elastic properties and thermal expansion coefficients of medium and high modulus graphite fibers , 2005 .

[4]  Dick den Hertog,et al.  Space-filling Latin hypercube designs for computer experiments , 2008 .

[5]  Andy J. Keane,et al.  Engineering Design via Surrogate Modelling - A Practical Guide , 2008 .

[6]  Jean Pierre Pascault,et al.  Glass transition temperature versus conversion relationships for thermosetting polymers , 1990 .

[7]  J. Svanberg,et al.  Predictions of manufacturing induced shape distortions : high performance thermoset composites , 2002 .

[8]  Robert Hein,et al.  Prediction of Process-Induce Distortions and Residual Stresses of Ancomposite Suspension Blade , 2015 .

[9]  M. Elseifi,et al.  PROBABILISTIC ANALYSIS OF THICK COMPOSITE PLATES WITH MANUFACTURING AND MATERIAL UNCERTAINTIES , 2001 .

[10]  Joaquín López,et al.  Isothermal curing by dynamic mechanical analysis of three epoxy resin systems: Gelation and vitrification , 2002 .

[11]  Ivana K. Partridge,et al.  Cure modeling and monitoring of epoxy/amine resin systems. II. Network formation and chemoviscosity modeling , 2000 .

[12]  A. Johnston,et al.  An integrated model of the development of process-induced deformation in autoclave processing of composite structures , 1997 .

[13]  J. Holmberg,et al.  An experimental investigation on mechanisms for manufacturing induced shape distortions in homogeneous and balanced laminates , 2001 .

[14]  C. C. Chamis,et al.  Simplified composite micromechanics equations for hygral, thermal and mechanical properties , 1983 .

[15]  Nima Zobeiry,et al.  Viscoelastic constitutive models for evaluation of residual stresses in thermoset composites during cure , 2006 .

[16]  Peter Wierach,et al.  Determination of volumetric shrinkage of thermally cured thermosets using video- imaging , 2016 .

[17]  Robert Hein,et al.  FE-BASED PREDICTION OF PROCESS INDUCED DISTORTIONS AND RESIDUAL STRESSES FOR CFRP FRAMES , 2015 .

[18]  A. Olsson,et al.  On Latin hypercube sampling for structural reliability analysis , 2003 .

[19]  Reza Vaziri,et al.  Probability-Based Modelling of Composites Manufacturing and Its Application to Optimal Process Design , 2002 .

[20]  Kwang Joon Yoon,et al.  Effect of Thermal Deformation and Chemical Shrinkage on the Process Induced Distortion of Carbon/Epoxy Curved Laminates , 2001 .

[21]  Farrokh Mistree,et al.  Kriging Models for Global Approximation in Simulation-Based Multidisciplinary Design Optimization , 2001 .

[22]  T. Simpson,et al.  Computationally Inexpensive Metamodel Assessment Strategies , 2002 .

[23]  Martin Wiedemann,et al.  EVo: Net Shape RTM Production Line , 2016 .

[24]  J. Raghavan,et al.  Experimental study of tool–part interaction during autoclave processing of thermoset polymer composite structures , 2010 .

[25]  S. Sriramula,et al.  Quantification of uncertainty modelling in stochastic analysis of FRP composites , 2009 .