Experimental study on regaining the tangential velocity energy of axial flow pump

Axial flow pumps are widely used in a wide range of applications. Although a different range of axial pump designs can be observed, axial flow pumps are usually designed for high flow rate and low pressure applications. In this study, two different axial flow pump impellers with and without guide vanes are experimentally investigated. The impellers used in the experiments consist of three and four blades. The guide vanes have seven vanes. The experimental set up mainly includes an axial pump, electrical drive motor, storage and calibration tanks and control system. Different impellers are attached to the pump, and the pump characteristics are obtained. As a result of the investigation, it is found that using guide vanes and regaining the tangential velocity energy of the pump improves the total pump efficiency about 3%. Also, the maximum efficiency improvement is obtained at 1000 rpm using guide vanes with a four blade impeller as 65.3%.

[1]  Alexey J. Stepanoff.  Turboblowers : theory, design and application of centrifugal and axial flow compressors and fans , 1955 .

[2]  J. H. Horlock.  The Use of Circumferentially Varying Stagger Guide Vanes in an Axial Flow Pump or Compressor , 1990 .

[3]  A. de Kovats,et al.  Pumpen, Ventilatoren und Kompressoren : radialer und axialer Bauweise , 1968 .

[4]  B. Lakshminarayana.  Methods of Predicting the Tip Clearance Effects in Axial Flow Turbomachinery , 1970 .

[5]  J. F. Combes,et al.  Numerical and Experimental Analysis of the Flow in a Centrifugal Pump at Nominal and Partial Flow Rate , 1992 .

[6]  William N. Dawes,et al.  Development of a 3D Navier Stokes Solver for Application to all Types of Turbomachinery , 1988 .

[7]  M. L. Billet,et al.  A Correlation of Leakage Vortex Cavitation in Axial-Flow Pumps , 1994 .

[8]  W. C. Zierke,et al.  Flow Visualization and the Three-Dimensional Flow in an Axial-Flow Pump , 1996 .

[9]  G. K. Serovy,et al.  Modeling the 3-D Flow Effects on Deviation Angle for Axial Compressor Middle Stages , 1986 .

[10]  H. N. Michael.  Centrifugal and axial flow pumps: by A. J. Stepanoff. 428 pages, illustrations, diagrams, 15 × 24 cm. New York, John Wiley & Sons, Inc., 1948. Price, $7.50 , 1948 .

[11]  Durmus Kaya,et al.  A study of axial flow pump impellers -effects of pump design parameters on its performance , 2000 .

[12]  P. D. Taylor,et al.  An experimental investigation of the flow through an axial-flow pump , 1995 .

[13]  G-L. Liu.  Optimization of Axial-Flow Pump Cascade Solidity Subject to Cavitation- and Separation-Free Constraints , 1995 .

[14]  Sumio Saito.  Generation Mechanism and Transition Process of Cavitation Noise , 1989 .

[15]  M. Mory,et al.  Tip Clearance and Tip Vortex Cavitation in an Axial Flow Pump , 1997 .

[16]  Budugur Lakshminarayana,et al.  End-Wall and Profile Losses in a Low-Speed Axial Flow Compressor Rotor , 1985 .

[17]  S. M. Miner,et al.  Potential Flow Analysis of the Forces on a Laboratory Centrifugal Pump Impeller , 1992 .

[18]  K. Alpan,et al.  SUCTION REVERSE FLOW IN AN AXIAL-FLOW PUMP , 1991 .

[19]  A. Goto.  Study of Internal Flows in a Mixed-Flow Pump Impeller at Various Tip Clearances Using Three-Dimensional Viscous Flow Computations , 1992 .