A Sequential Fluid-mechanic Chemical-kinetic Model of Propane HCCI Combustion

We have developed a methodology for predicting combustion and emissions in a Homogeneous Charge Compression Ignition (HCCI) Engine. This methodology combines a detailed fluid mechanics code with a detailed chemical kinetics code. Instead of directly linking the two codes, which would require an extremely long computational time, the methodology consists of first running the fluid mechanics code to obtain temperature profiles as a function of time. These temperature profiles are then used as input to a multi-zone chemical kinetics code. The advantage of this procedure is that a small number of zones (10) is enough to obtain accurate results. This procedure achieves the benefits of linking the fluid mechanics and the chemical kinetics codes with a great reduction in the computational effort, to a level that can be handled with current computers. The success of this procedure is in large part a consequence of the fact that for much of the compression stroke the chemistry is inactive and thus has little influence on fluid mechanics and heat transfer. Then, when chemistry is active, combustion is rather sudden, leaving little time for interaction between chemistry and fluid mixing and heat transfer. This sequential methodology has been capable of explaining the mainmore » characteristics of HCCI combustion that have been observed in experiments. In this paper, we use our model to explore an HCCI engine running on propane. The paper compares experimental and numerical pressure traces, heat release rates, and hydrocarbon and carbon monoxide emissions. The results show an excellent agreement, even in parameters that are difficult to predict, such as chemical heat release rates. Carbon monoxide emissions are reasonably well predicted, even though it is intrinsically difficult to make good predictions of CO emissions in HCCI engines. The paper includes a sensitivity study on the effect of the heat transfer correlation on the results of the analysis. Importantly, the paper also shows a numerical study on how parameters such as swirl rate, crevices and ceramic walls could help in reducing HC and CO emissions from HCCI engines.« less

[1]  D. Foster,et al.  Compression-Ignited Homogeneous Charge Combustion , 1983 .

[2]  John B. Heywood,et al.  Internal combustion engine fundamentals , 1988 .

[3]  Robert W. Dibble,et al.  Sensitivity of Natural Gas HCCI Combustion to Fuel and Operating Parameters Using Detailed Kinetic Modeling , 1999, Advanced Energy Systems.

[4]  A. A. Amsden,et al.  KIVA3. A KIVA Program With Block-Structured Mesh for Complex Geometries , 1993 .

[5]  Neil Watson,et al.  A Non-Linear Digital Simulation of Turbocharged Diesel Engines Under Transient Conditions , 1977 .

[6]  Norimasa Iida,et al.  Self-ignition and combustion stability in a methanol fueled low heat rejection ceramic ATAC engine - Analysis of cyclic variation at high wall temperatures and lean burn operation , 1997 .

[7]  Hajime Ishii,et al.  Exhaust Purification of Diesel Engines by Homogeneous Charge with Compression Ignition Part 1: Experimental Investigation of Combustion and Exhaust Emission Behavior Under Pre-Mixed Homogeneous Charge Compression Ignition Method , 1997 .

[8]  Yoichi Ishibashi,et al.  Improving the Exhaust Emissions of Two-Stroke Engines by Applying the Activated Radical Combustion , 1996 .

[9]  G. Woschni.  A Universally Applicable Equation for the Instantaneous Heat Transfer Coefficient in the Internal Combustion Engine , 1967 .

[10]  Salvador M. Aceves,et al.  Compression Ratio Effect on Methane HCCI Combustion , 1998 .

[11]  Shuji Kimura,et al.  New Combustion Concept for Ultra-Clean and High-Efficiency Small DI Diesel Engines , 1999 .

[12]  Scott B. Fiveland,et al.  A Four-Stroke Homogeneous Charge Compression Ignition Engine Simulation for Combustion and Performance Studies , 2000 .

[13]  David E. Foster,et al.  Velocity Measurements in the Wall Boundary Layer of a Spark-Ignited Research Engine , 1987 .

[14]  Rowland S. Benson.  Chapter 6 – Heat Transfer in Engines , 1979 .

[15]  Bengt Johansson,et al.  Hydrocarbon (HC) Reduction of Exhaust Gases from a Homogeneous Charge Compression Ignition (HCCI) Engine Using Different Catalytic Mesh-Coatings , 2000 .