A Novel Design Method for Nonuniform Lattice Structures Based on Topology Optimization

Lattice structures are broadly used in lightweight structure designs and multifunctional applications. Especially, with the unprecedented capabilities of additive manufacturing (AM) technologies and computational optimization methods, design of nonuniform lattice structures has recently attracted great research interests. To eliminate constraints of the common “ground structure approaches” (GSAs), a novel topology optimization-based method is proposed in this paper. Particularly, the structural wall thickness in the proposed design method was set as uniform for better manufacturability. As a solution to carry out the optimized material distribution for the lattice structure, geometrical size of each unit cell was set as design variable. The relative density model, which can be obtained from the solid isotropic microstructure with penalization (SIMP)-based topology optimization method, was mapped into a nonuniform lattice structure with different size cells. Finite element analysis (FEA)-based homogenization method was applied to obtain the mechanical properties of these different size gradient unit cells. With similar mechanical properties, elements with different “relative density” were translated into unit cells with different size. Consequently, the common topology optimization result can be mapped into a nonuniform lattice structure. This proposed method was computationally and experimentally validated by two different load-support design cases. Taking advantage of the changeable surface-to-volume ratio through manipulating the cell size, this method was also applied to design a heat sink with optimum heat dissipation efficiency. Most importantly, this design method provides a new perspective to design nonuniform lattice structures with enhanced functionality and manufacturability.

[1]  Glaucio H. Paulino,et al.  Topology optimization with manufacturing constraints: A unified projection-based approach , 2016, Adv. Eng. Softw..

[2]  Xiaoming Wang,et al.  A level set method for structural topology optimization , 2003 .

[3]  Ole Sigmund,et al.  A 99 line topology optimization code written in Matlab , 2001 .

[4]  Prabhat Hajela,et al.  Genetic Algorithms in Structural Topology Optimization , 1993 .

[5]  David W. Rosen,et al.  Computer-Aided Design for Additive Manufacturing of Cellular Structures , 2007 .

[6]  M. Gilbert,et al.  Layout optimization of large‐scale pin‐jointed frames , 2003 .

[7]  C. Sun,et al.  Prediction of composite properties from a representative volume element , 1996 .

[8]  Ercan M. Dede,et al.  Topology Optimization, Additive Layer Manufacturing, and Experimental Testing of an Air-Cooled Heat Sink , 2015 .

[9]  A. Diaz,et al.  On Optimum Truss Layout by a Homogenization Method , 1993 .

[10]  H. Wadley.  Cellular Metals Manufacturing , 2002 .

[11]  Y. F. Zhao,et al.  Lattice-skin structures design with orientation optimization , 2015 .

[12]  George I. N. Rozvany,et al.  A critical review of established methods of structural topology optimization , 2009 .

[13]  N. Kikuchi,et al.  Solutions to shape and topology eigenvalue optimization problems using a homogenization method , 1992 .

[14]  W. Achtziger.  On simultaneous optimization of truss geometry and topology , 2007 .

[15]  M. Ashby,et al.  Cellular solids: Structure & properties , 1988 .

[16]  M. Bendsøe,et al.  Optimization methods for truss geometry and topology design , 1994 .

[17]  Christopher B. Williams,et al.  Multiple-Material Topology Optimization of Compliant Mechanisms Created Via PolyJet Three-Dimensional Printing , 2014 .

[18]  Ian Gibson,et al.  Additive manufacturing technologies : 3D printing, rapid prototyping, and direct digital manufacturing , 2015 .

[19]  C. Beyer,et al.  Design and Analysis of Lattice Structures for Additive Manufacturing , 2016 .

[20]  Matthew Gilbert,et al.  Rationalization of trusses generated via layout optimization , 2015 .

[21]  W. Lu,et al.  Evolutionary design of nonuniform cellular structures with optimized Poisson's ratio distribution , 2018 .

[22]  T. Dbouk,et al.  A review about the engineering design of optimal heat transfer systems using topology optimization , 2017 .

[23]  Ole Sigmund,et al.  Manufacturing tolerant topology optimization , 2009 .

[24]  R. Poprawe,et al.  Laser additive manufacturing of metallic components: materials, processes and mechanisms , 2012 .

[25]  M. Bendsøe,et al.  Generating optimal topologies in structural design using a homogenization method , 1988 .

[26]  M. Bendsøe,et al.  Topology Optimization: "Theory, Methods, And Applications" , 2011 .

[27]  Taeyoung Lee,et al.  Geometric numerical integration for complex dynamics of tethered spacecraft , 2010, Proceedings of the 2011 American Control Conference.

[28]  Martin P. Bendsøe,et al.  Optimization of Structural Topology, Shape, And Material , 1995 .

[29]  Ole Sigmund,et al.  On the Design of Compliant Mechanisms Using Topology Optimization , 1997 .

[30]  David Rosen,et al.  Design of truss-like cellular structures using relative density mapping method , 2015 .

[31]  Weihong Zhang,et al.  Scale‐related topology optimization of cellular materials and structures , 2006 .

[32]  M. Ashby,et al.  Effective properties of the octet-truss lattice material , 2001 .

[33]  Albert C. To,et al.  Efficient Design-Optimization of Variable-Density Hexagonal Cellular Structure by Additive Manufacturing: Theory and Validation , 2015 .

[34]  Yaoyao Fiona Zhao,et al.  A Survey of Modeling of Lattice Structures Fabricated by Additive Manufacturing , 2017 .

[35]  Paul Witherell,et al.  Investigating the Role of Geometric Dimensioning and Tolerancing in Additive Manufacturing , 2015 .